DLE1310W (ABWEEUS) LG Dryer - Instructions

An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.

Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

Slide out old filter then slide in the new one.

Followed video provided on site

After trying duct tape to fix the tear, I decided to see if I could just order a new one. Part Select was the first company I found listed, so I ordered one. It was not expensive and it was delivered very quickly! It works so well s as me I’m a very happy customer!

Slide out the old lint catcher, and slid in the new one, not that hard.

Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

Removed old lint filter inserted a new one.

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.

First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)