DCVH515EF3WW General Electric Dryer - Instructions

I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.

Took dryer apart replaced felt seal and the four drum slides put it back together works better now than when it was new!!!!!!

I looked on you tube and was able to determine the cause and order the parts I needed to rectify the issue. I removed the the top panel and the front panel. I replaced the bearing.

the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.

good replacement procedure on you tube.

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine

I first watched the video on how to. Being mechecanically inclined I dismantled and removed everything needed to replace the drum bearing. Also removed belt at the same time. I replaced the bearing, then the belt. The belt could be a little tricky for some people. Getting the belt on the tension pulley could be a problem. What I did was I got a large nylon tie and put it around the armature of the motor. I then retracted the pulley just enough to be able to slip the belt over it. Of course this is all performed through the limited space on the bottom left, between the drum and the dryer shell. Once on the pulley, I cut the tie with wire cutters and it snapped into place. Rotated the drum a couple of times to line the belt with the pulley, perfect. I then put everything back together. I also cleaned any and all the lint that had gathered throughout the exhaust. Pluged the dryer in, perfect. Just like new. One more note getting the parts was so easy also. Your website and how to demo was a great help. Thank you, thank you very much. The words of the late Elvis Presley. They never get old.

I bought the Heating Element and Housing together so that I would not have to stretch and run the coils and to save time!
1. I removed the two screws that hold the top down by opening the dryer door and removing the two screws at the top of the door opening. Then I pulled the top off.
2. Then I removed the two screws on the top inside of the dryer on the left right and took the front off.
3. Next I spread the dryer open a little and pulled the drum out while pushing the belt off the back of the drum.
4. Then I removed the screws to the sensors and removed them from the housing.
5. Then I removed the four screws holding the heating element housing to the back of the dryer and took it out and put in the new peace.
6. Do everything in reverse when putting the dryer back together.

I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken

Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.

TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY

Used a flash light to see, reached in and installed new bulb above the door

I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.

I followed the directions I found on my tablet on youtube.