D1435BB LG Dishwasher - Instructions

Very easy just took out two screws that held the dishwasher to counter top.Then pulled dishwasher out just far enough that both door cables are exposed.The hardest part for me was getting the spring stretched enough to clip on.This was a easy installation for most people.

I am 77 years old and got it all on but the corners did not want to go in so I had to call my grandson and he got them in. It still leaked on the bottom left side. It is getting old (11 yrs) so I decided to get a new one. It is actually pretty simple to install, but it does take a little strength.

Old door seal appeared ok, no rips and seated evenly all around. Pulled that seal out and replaced with new. Seated new door seal after wetting inserted lip. Tested...leak greatly reduced, but still dripping. Removed seal, placed a rubber rope (same rope used for screening) within the tub recess, then reseated new seal. leak ceased. Also replaced the reservoirs on the left side of the cabinet (guide assembly). Old reservoir had debris within so decided to replace. Used regular pliers for the 3 hose spring clamps underneath, and a pair of large neede nose pliers for the fill flange (regular thread).

Replaced it . Simple

Removed two screws (one each side) and the toe kick plate at the bottom. Slide the dishwasher out from the cabinets about 10", remove broken cord clip from door and spring. Install door clip and wrap cord around pulley , attach to spring then attach spring to door, lifting the door will help attach the spring. Do one side of the door at a time.

Cables have broken about every 3-6 months after original ones broke after 8 years. Removed front kick plate screws and remove kick plate, and remove two top screws holding Dishwasher to counter-top. Pull dishwasher out about 10 inches. Remove all broken parts and replace cables. Side dishwasher back in place and reinstall removed screws. I just hope these Cables last longer than the ones I had bought from another source. I have replaced those Cables 5 times already and hope these last MUCH longer. Delivery was very fast from PartSelect.

snapped on new axel-wheel assembly

connector was broken. just attached new connector to spring on each side of door. easy fix.

Followed the video provided by your company, done like 1,2,3

I watched the video and it showed every step to remove the old part and replace the new one. Went fairly easy except when put the new motor in the new seal was difficult to put on. I think if I would taken off the front door I could have got close to the back of the rubber seal to secure it a little easier. Had to use a rubber hammer hold my breath to not brake the plastic motor. But that was only way I could get in. The video showed it going rely easy that was not the case because it was a new seal. In the end it all worked out.
Thanks for the video's to help

The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.

I would just like to return these rollers and would like a return address.

Thank you!
Penelope

same as in the video , but the double red wire is on the wrong terminal you have to break the plastic housing on the dishwasher and put it on the first one next to the white wire .if you hook it up the way it is the dishwasher wont work and when you open the door the dishwasher turns on . watch the video real close when it gets to the wire connections you see the double red wire goes over one pin to the one next to the white wire . works fine after that.

Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.