CVE3400W Jenn-Air Cooktop - Instructions

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

number to get the correct part was problem. item number was a whirlpool number. all other soureces i could not get the part. part selec t was able to come up the whirlpool item number. when i received the correct part it did not take long repair the problem. thank you for all your help.

Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done

Just placed new filter in slot

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

Couldn't hook up the wires since the instructions were so cryptic. Ended up fixing old control and re-installed it. Worked fine.

very easy slip in

I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)

simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

The repairs was really easy. All you had to do was remove the screws holding the glass top surface down, raise it up, then start by pulling one wire at the time and plugging it into the new element. Then bolt the glass top surface down and it was ready to use, good as new.

This was a repair project on a Jenn-Air built-in stovetop, which I had trouble finding instructions on how to disassemble. My particular problem was that three of the four burners had no temperature control. They were either on high or off - no such thing as simmer. This is opposite the problem described as a normal indicator of burner control failure. Usually the burner just goes dead. The hardest part of the repair was accessing the metal plate the burner controls are mounted on. First, I flipped the circuit breaker to the stovetop. It will shock the cr@#p out of you if you don't (I have experience from poking around down there without turning the power off). First, I had to remove the two burner inserts. The left one lifted from the top and the right one lifted from the bottom. Don't lift them past about 30 degrees. They are meant to lift up just enough to clear the tray well and then slide out. After removing the burner inserts, I was able to unscrew the eight fasteners holding down the stovetop rim. After removing this, I pulled out the trays underneath the burner inserts and put them aside without unscrewing the ground wires that attach them to the stovetop chassis. After removing the two screws holding on the active burner indicator lights, I was able to pull it up and lay it aside. Then I had to unscrew the two large brackets under the cabinet to loosen up the stovetop chassis so I could lift the front of it up an inch from the cabinet to enable me to unscrew two small metal screws that attach the metal plate holding the burner controls. After removing the two screws holding each burner control to the metal plate, I could unplug each of the five wires from the old controllers and plug them into the new controllers, in turn, before reattaching the new controllers to the metal plate. After repeating this procedure two more times, I reversed the process to reassemble the stovetop and voila, turned on the power and it worked perfectly. The result; a happy wife. For today.

Here is what I did with new switch (part#12002125) and it worked. Connect jumper to P1 and S1. Split the 2 red wires and put new spades on the ends, then put the red wire from left front switch on P2 and the other red wire from the right rear burner on 2. Blue goes to 4. Purple goes to 4A. Black goes to P1. Orange goes to S2.

the filter fit because the scale in the photo allowed me to choose which one to buy!

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.