CVE3400B Jenn-Air Cooktop - Instructions

number to get the correct part was problem. item number was a whirlpool number. all other soureces i could not get the part. part selec t was able to come up the whirlpool item number. when i received the correct part it did not take long repair the problem. thank you for all your help.

Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

raising the cook top on to 2x2s, one on each end, allowed me to remove the 9 sheet metal screws that keep the glass top fastened to the box containing all of the heating elements and controls. After removing the control knobs and the glass top, everything was clearly visible. Removing the four screws that hold the control box frame in place allowed me to turn the switches upside down and photograph the placement of all of the wires on the pins. I then transferred the wires from the old switch to what I thought were the corresponding pins on the new switch(the replacement switch has more pins, and they are not located in exactly the same spots as the old switch). When I turned the power back on, the switch turned the burners on, I had heat but the indicator lights didn't work. I turned the breakers back off and rewired according to a previous commentors wiring directions(his model was not exactly the same as mine), the indicators worked but I was back to no heat. I called my son, who has his own commercial electric company,and he looked at my photos from before, the diagram that came with the new switch, and it took him about 15 minutes to reconnect the pins to different wires and when we turned the power back on---both indicators and heating elements worked. It was the dual switch and double indicator that made it more complex to figure out. Nice to have very smart kids.

Just needed to replace a scratched up grill on my stove top. The black paint was scratched off and looked horrible. You site made it very easy to find what I needed and it got here in two days. If I had known it was going to be that quick and easy, I would've done it a long time ago! Thanks!

Just placed new filter in slot

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

Couldn't hook up the wires since the instructions were so cryptic. Ended up fixing old control and re-installed it. Worked fine.

Took the old one out, plopped the new one in.

very easy slip in

simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)

Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.