EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Keep typing for more specific results...
Models > CME9010CAE > Instructions

CME9010CAE Maytag Microwave - Instructions

All Instructions for the CME9010CAE
16 - 30 of 61
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Died while heating lasagna
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.
Parts Used:
Microwave Ceramic Fuse 20 Amp
  • connie from madison, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
9 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave went pop and nothing would work.
I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.
Parts Used:
Microwave Ceramic Fuse 20 Amp
  • Deborah from STRUM, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace bulb under the microwave
Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.
Parts Used:
Microwave Light Bulb (40w)
  • Verne from HENDERSONVLLE, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light bulb out
Put s pot under were you take the screw out.If you drop it you can get it easy
Parts Used:
Microwave Light Bulb (40w)
  • Joe from RAIL RD FLAT, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
There was a minor explosion in my microwave that shattered the ceramic shelf that forms the bottom of the inside of the microwave.
Called parts select and discussed the situation and they identified the correct replacement shelf. When I received it, I just pushed it into place (the edges of the shelf are coated with a rubber seal) and it is there. The unit looks like new. It was great to be able to find a part for an appliance from 1988!
Parts Used:
Glass Tray/Shelf - White
  • Martin from newtown, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken microwave handle
Having a broken microwave door handle was driving me crazy! I never realized how often I opened/used the microwave. I ordered the part on a Sat. and had the replacement by Mon. - now that's service! My husband fixed the handle in a matter of minutes and the microwave is as good as new!

Thanks!

Lori
Flatwoods, Ky.
Parts Used:
Grease and Air Filter Door Handle
  • Lori from Flatwoods, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
8 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lights bulbs burned out
Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.
Parts Used:
Microwave Light Bulb (40w)
  • Kat from Hudson, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb burnt out .
Turn off power supply at breaker . Replace old bulb with new bulb .
Parts Used:
Microwave Light Bulb (40w)
  • DAN from CARPENTERSVLE, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Range light bulbs were burned out
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Parts Used:
Microwave Light Bulb (40w)
  • Barbara from MERIDIAN, ID
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb burned-out
screwed in new bulb
Parts Used:
Microwave Light Bulb (40w)
  • Pablo from Burlingame, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Parts Used:
Microwave Light Bulb (40w)
  • Jerry from Pine, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out bulb
Husband replaced the bulb
Parts Used:
Microwave Light Bulb (40w)
  • Theresa from OVERLAND PARK, KS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light over range burned out
Philips screwdriver
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.

Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/delivery was fast. No need to have spare on hand.
Parts Used:
Light Bulb - 120V 25W
  • Vincent from CHICAGO, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to any microwave functions
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!
Parts Used:
Microwave Ceramic Fuse 20 Amp
  • Richard from CALIFORNIA, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out light in microwave
Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.
Parts Used:
Microwave Light Bulb (40w)
  • DANNY from SAINT JOHNS, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CME9010CAE
16 - 30 of 61