CFW5000FW0 Crosley Washer - Instructions

disconnected the power and water supply.

removed the back panel.

unscrewed the contol board that blocked access to the bottom of the shock absorber.

pulled the original pins out with pliers while pressing in the piece that prevents it from working its way out.

removed the shock absorber.

placed the new shock absorber in the bottom mount, put soap on the pin for lubrication and pushed it through the hole. Put the top of the shock absorber in its place and placed the other pin in.

replaced the control board and replaced the rear panel.

Codes did not point directly to the door lock, so that was a 50/50 between door lock and control board. With top of washer removed door lock is just a couple screws and 3 electrical connections.

Belt was worn and frayed. Belt replacement was tricky because new belt was so tight. Used vice grips to lightly hold belt on pulley while using screwdriver through spokes into tub back to ratchet/control pulley. Not too bad.

Works like new!

Take off the back, one of the shock absorbers was broken, it was very obvious. Looked up part at partselect.com, very easy, ordered part, it came in 2 days, the repair took another 15 minutes. There were directions inside the repair part to tell you a trick to get the old one off. It worked like a charm. Why spend $200-300 or more on a repair on a $500 washer when you can do the entire job for about $30 and get it back working in 2 days!! No brainer.

I just removed the 2 screws, removed the old striker and replaced it with the new one. The entire project took 3 minutes.

Went on line to your site , found part, read how easy it was for others to repair. So ordered part and replaced myself. I am a woman who's husband is not handy fixing things and it took me no time at all to remove and replace part. Thanks to others who shared how they did in this situation.Much cheaper to repair yourself. You can do it!!

The top, control panel and front and back of the machine are removed - all by just removing simple sheet-metal screws. NOTE: remove the soap drawer, because there are two longer screws behind the drawer front. When replacing these later, get them just snug because "tight" will crush the supporting plastic. Don't bother to unplug all the wires to the control panel - just tape it to the top of the machine so it doesn't fall. The rubber part to be replaced is held to the machine by three large spring-held bellows clamps. Squeeze the ends with a pair of pliers and slide them off the tubing. When putting the new part on, I found that the cramped space and difficult access made getting two of the spring-held bellows clamps impossible to get back on, so I used automotive-style stainless hose clamps, which screw tight from the side. Be cautious to get them very snug but not super tight because, you can crush the plastic tubing to which you are fastening. Reassembly of the panels on the machine is the reverse.

Great advice on your site.
Repairman "found bad motor control board" and gave me an estimate of $316.00 to repair. I figured that the $80 gamble was worth a shot. Took the top screws off, slid the top back and in less than 15 min. I had a fully functioning washer. Thank you.

took out door lock and switch assembly replace with a new one and it work

After viewing the installation video, I decided not to attempt this and caled a repairman. He cautioned me not to replace the rubber if the only reason is the moldy smell. He said that the mold will reappear in a couple of years and that regular cleaning will help combat the problem. He said that replacing the bellows should be limited to necessity such as leaking.

Pulled off front panel and found broken shocks. Ordered from Parts Select and replaced within 15 minutes. It was a little tricky replacing as they came out due to poor access from the rear. Make sure to regrease palstic pins and she is running like new.

I read the input of others who had this problem with this washer and how they had replaced the door lock and switch assembly. I figured it was worth the $70-$80 part versus the $540 repair or purchasing a new machine. I was really happy with the machine until this problem occurred.
When I got the new part.....I unplugged the machine. Took out two screws in the back of the top panel. Removed the top of the machine. Took out two screws in the front of the machine that hold the door lock ans switch assembly into place. I unplugged the three wires from the old part (be careful not to drop the old or new part....if you choose to do this by reaching in from the top like I did for this repair.....easier than removing the entire front of the machine.)
I plugged the three wires into the new part and positioned the new part in the door lock position. Replaced the two screws. Put the cover back on the top and replaced the two screws that hold the top cover on the machine.
I was thrilled when it worked perfectly. What a relief!
Sure glad I looked at this website and tried this! The repairman really didn't know enough about my machine....obviously. I'd like to call him and tell what was really wrong so next time he'll know.

Removed the the two screws holding access panel on the bottom front. Shocks use two plastic retaining pins on each shock. Used a screwdriver to push down on the locking tab on the plastic retaining pin ant pushed out. One of the pins is behind the water pump and a bit harder to access. I used a socket with an extension to push it out. installed new shocks with old pins and was back in business. Shocks go in a certain way so be sure to look at the instructions that come with the replacement shocks. Note: the replacment shocks that came don't look anything like the originals. Originals looked more like an automotive shock. Also as both shocks were broken, I ordered two, not knowing that they come two to a package. When you order that is not clear. So now I have an extra set, which might not be bad to have on hand. Kit also comes with an extra pin in case you break one.

After removing the front of the washer, I used slip joint pliers for the hose clamps, then a screwdriver for the mount bolts and replaced the pump motor in reverse order. The pump was ordered on line on a Friday before 10am and was delivered on saturday moring by FedEx. I could not have expected such fast and efficent service!
Great Job!!

remove side panel & start rinse cycle & heard a grinding noise in discharge pump. used a bucket to catch water upon removeal of discharge hose to pump. unplug disconnect plug to motor, remove pump from unit. Discovered propeller was loose in housing. Googled Partselect.com, odered part & in 2 days later installed new pump on unit. Started a load of wash & it has been working perfect ever since. thanks to PartSelect.com for the service, the repair was minimal & easy for the DO IT YOURSELFER. Bill Starry

Replaced the old striker with the new one in about 5 minutes. Just needed a phillips screwdriver. Unbelievable how hard it was to find the part at local store...much easier to order from partselect. If I break it again, I will be all set. Part cost $7 vs repairman visit at a cost of at least $200 - - was worth the effort.