CDBEH600SW2A Frigidaire Dishwasher - Instructions

The pump was progressively getting noisier over time to the point we could hear it in the back of the house. The dishes were always clean though. Turned off breaker. Removed two screws attaching unit to cabinet. Pulled out unit as far as I could and disconnected power. Turned unit slightly so I could reach water connection and disconnected it. Disconnected flexible drain hose, then could pull unit completely out of cabinet. Turned on it's side so I could access the motor. Removed two screws, steel retaining clip, then motor. Came with 2 new O rings which I lubricated and replaced. Reinstalled everything and problem solved, nice and quiet. One hour 15 minutes total.

Popped off the old spray arm ... INTENTIONALLY, and put new one in. Had to lift off small strainer to allow old arm to release! Be sure to turn arm until it clicks into place, return small strainer/clip, and you are in business!
Most trouble I had was getting this old bo
y up off the floor afterward.
Dished so much cleaner now!

The door seal comes off easy. No need to take apart the door. The new seal fits snug. Make sure the notch on the right side of the door seal is installed to the right side of the bottom of door

I went to your website found part# and parts diagram and ordered parts . I picked standard shipping . That evening e-mailed me they were instock and shipped also gave tracking # thet parts were here the next day.I removed the front dec panel then the 4 nut& bolts holding door to hinges(with door in closed position).Then I removed the 2 screws holding the hinges to the frame/axle. Replaced hinges with new ones .Put screws back in frame/axle . Put 4 nut and bolts back to secure door to hinges . Then i reinstalled under counter put new wheels on lower rack . I then filled it with dishes and ran a long cycle checked for leaks THEIR WERE NONE!!! THANK GOD !! Job complete, Thanks parts direct for a well designed website and detailed pics and parts#. TIM

Easiest repair ever. Part came quickly & came fully assembled. Just screwed the part on by hand and it has worked like new ever since. The original part is 3 separate pieces but the new part was all in one & fit perfectly.

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

It is rather easy to repair. After you remove the screws that secure the top of the dishwasher to the countertop you can slide the disherwasher out far enough to gain access to the hose. The hose pulls off after you slide the spring clips down the hose far enough so they no longer grab. Then simply reverse the order and you're done. Less than 30 minutes and you should no longer have to hand wash your dishes!

replaced with new lower rack, out with the old, in with the new! Shipping was great new part arrived in 2 days! Great service, and will use again for all parts needed in the future, and will tell everyone about this site! Thanks a bunch!

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

found spray arm on the rack looked at the top of rack saw a nut screw the nut looked at the clip found the ears broke off easy r&r.

Remove the lower dish tray and set aside. Remove two Phillips screws on each side of inner liner, then close door. You should then be able to slip off the external facing (set aside). Pull lower gasket toward tub until fully removed. Reinsert the new gasket into the same tight slot, making sure that the notch inserts into the slot and the flexible gasket runs the full length of the tub. The gasket should bow out slightly toward the tub. Also make sure that the side seals do not interfere with the bottom seal fully mating with the floor of the tub. Close the door and check to make sure the lower gasket reveal is the same across the length of the inner liner. Reinstall the dish tray, then reinstall the external facing, using the same four Phillips screws to secure. Test sealing by running a short cycle on the dishwasher.

Simple repair.

First let me say I love this company, I have used them before and I will use them again.
Parts arrived quickly, unwrapped them, put the video
supplied by this site on my phone and the entire project was done in less than ten minutes. My dishwasher works like new. Thank you !

Slid dishwater out from cabinet, replace cable, slid unit back in , secure ---done! door has tension now.