EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Keep typing for more specific results...
Models > CAW35114GW0 > Instructions

CAW35114GW0 Crosley Washer - Instructions

All Instructions for the CAW35114GW0
61 - 75 of 249
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Parts Used:
Washer Drive Pulley
  • JERRY W. from CARROLLTON, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gear stripped on main spline
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Parts Used:
Washer Drive Pulley
  • Bernard from ARIZONA CITY, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plastic teeth on the inside of the large agitator stripped out.
I needed an air impact wrench to remove the single nut. It was stuck on there. Once the Nut. Was removed it was an easy repair. Perfect fit! Just pop it on the shaft and replace the bolt. Since I had my air tools out already I gave it a couple of dugga duggas.
Parts Used:
Agitator Kit
  • David from NICHOLASVILLE, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer struts were wore out
Removed the old and replaced with new
Parts Used:
Suspension Rod Kit
  • Michael from GEORGETOWN, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wanting to see this new energy efficient washer work, with the lid open
There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.
Parts Used:
STRIKE
  • Terry from KEYSTONE, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had to replace the agitator
I already had the old agitator out, so when I got the new one I put it in the tub. You have to spin it a little so it seats properly. I then tightened the bolt with a 7/16” socket and my wife was washing a load within 15 minutes
Parts Used:
Agitator Kit
  • Thomas from MENTOR, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Washer acted like the lid would not latch and stopped it from cycling.
My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!
Parts Used:
STRIKE
  • Mark from BELLEVUE, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom agitator stripped
Followed YouTube video

Excellent standard shipment time
Parts Used:
Washer Bottom Agitator
  • Therese from Cobb, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
fabric softener wasn't dispensing
The old part popped right off, and new one installed. Works Great!!!
Parts Used:
Washer Fabric Softener Dispenser
  • Carol from MT STERLING, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My washer was squealing on the spin cycle! Also shaking & moving!
We also purchased from this site the agitator repair kit! The youtube videos were extremely helpful!
Parts Used:
Washer Spacer Thrust
  • Donna from IRON MOUNTAIN, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set, Wrench (Adjustable)
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid strike broke
Removed old one (2 screws) slid in place and screwed in.
Parts Used:
STRIKE
  • Anna from TAWAS CITY, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Parts Used:
Washer Drive Belt
  • James from MAHWAH, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water inlet valve on the cold side wasn’t allowing color water flow
I watched the video and for the most part the first part of the repair went well. I carefully stored the screws, but despite what the video suggested the part did NOT just slide out. Upon further inspection I discovered two small screws in the top of the valve housing affixing it to the machine. Since it was to narrow an are to use a driver I was forced to remove the housing that holds the timer, which involved removing the knob and a small screw. On each side of the housing was a metal clip and true to form I was able to loosen one side but the other the clip launched into orbit. After a thorough inspection of the floor I found said clip. I was then able to remove the housing and loosen the two screws. Of interest is the fact that the new part had molded places for screws different that the video. After that replacing everything went smoothly and I was able to hook up the washer as the repair was successful.
Parts Used:
Water Inlet Valve
  • Linda from Lebanon, VA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Was it getting education out of the top agitator
I went to a site that helped me diagnose the potential problems with my washer. It was the dogs that had gone bad and we're no longer gripping the upper agitator. Socket set to go in and undo the bulb the holes the upper agitator in place. You just remove the assembly that holds the dogs and I used a new washer that goes in between the upper agitator and the lower agitator. Save beaucoup bucks and it's sort of empowering for a non mechanical person. The website scared me right to you guys. And I also bought another order we can involve the upper agitator and an extra set of those dogs. Awesome company! Customer service is incredible!
Parts Used:
Washer Spacer Thrust Washer Agitator Cam Kit
  • John from CASCO, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Partial Agitation - CAM Agitator teeth worn
1. Removed the fabric softener dispenser

2. Removed Barrier Seal Cover

3. Removed bolt and seal

4. Removed and replaced CAM Agitator Assembly

5. Reversed the removal steps.
Parts Used:
Agitator Kit
  • Joseph from Jupiter, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CAW35114GW0
61 - 75 of 249