79570323311 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
After 10 years of service the right door gasket needed replacement.
It was SO easy. No clamps or brackets. Grabbed the gasket with pliers to get started removing it - just pull it out of the deep groove inset around the perimeter of the door. Within one minute I had the old gasket removed. Started installing the new gasket by inserting the top right corner 1st (pushing the new gasket profile into the deep groove inset on the door). Working around the top and right side slowly inserting the gasket profile into the deep groove around the entire door. You may have to "adjust" a bit by pulling on the gasket but within 5 minutes I had the new gasket in-place never having to turn off the refrigerator. YouTube has great "how-to" videos. It's easy!
Parts Used:
-
MIKE from MENASHA, WI
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken flapper spring in kenmore elite refrigerator door
-
Sam from SAINT JOSEPH, MO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring broken in door mullion
Took 2 screws out and disconnect wire and install new part.
Parts Used:
-
Wayde from SEMINOLE, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice tray was not rotating any longer
-
Angela from SAINT JOSEPH, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Removed old part.
-
Steve from NORTH AURORA, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old part did not seal properly
Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.
Parts Used:
-
Donald from MERRITT IS, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Remove and replace cracked crisper drawer cover frame
1) Remove three drawers and items sitting on glass shelf.
2) Remove glass shelf
3) Remove entire crisper plastic unit from refrig.
4) Unscrew 6 screws holding uprights with a philips head screwdriver.
5) Remove top frame and replace with new frame.
6) Replace 6 screws and tighten them.
7) Replace entire frame in refrig and replace 3 drawers and glass shelf.
8) Done
2) Remove glass shelf
3) Remove entire crisper plastic unit from refrig.
4) Unscrew 6 screws holding uprights with a philips head screwdriver.
5) Remove top frame and replace with new frame.
6) Replace 6 screws and tighten them.
7) Replace entire frame in refrig and replace 3 drawers and glass shelf.
8) Done
Parts Used:
-
H Bartlett from JENSEN BEACH, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken spring on flapper door
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Parts Used:
-
Richard from IMPERIAL, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace water filter
Followed directions that came with the filter. Did remove the top shelf for easier access. Very simple and quick.
Parts Used:
-
Bill from FORT SMITH, AR
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The spring on the mullion was broken so the mullion would not open to seal the other door.
I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.
Parts Used:
-
JANET from GRAND JCT, CO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.
Followed Youtube video provided on the PartsSelect Website:
https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST
Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST
Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
Parts Used:
-
Robert from WARREN, RI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rail that holds meat tray broken
remove all trays from refrigerator , remove screw holding rail and install new rail.
Parts Used:
-
Steve from GEORGE WEST, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior light switch not working
Remove two screws on top of the fridge; removed old switch and inserted new switch. Worked like a charm. Replace casing and screws.
Parts Used:
-
Sharon from HOULTON, ME
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken handle/ stripped fastening screws
removed old handle
Installed new handle with hex wrench used to tighten up
Installed new handle with hex wrench used to tighten up
Parts Used:
-
Faison from EDENTON, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Stopper had snapped off
Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!
Parts Used:
-
Lawrence from FALL RIVER, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!