66595794000 Kenmore Range - Instructions

Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.

As a former appliance repairman, the installation went just like the repair instruction video.
Just use care not to scratch anything and clean behind the appliance and cabinet walls, etc. It's worth a hug and a piece of pie!

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.

Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.

1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall

turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers

Remove the old part and install the new part.

looked on internet on how to remove top. an easy fix after watching video

I disconnected power cord from house current. Removed back panels (2). I then removed round knob on front of range. I then removed the 2 screws holding the switch in place. After doing that, I gently removed the actual switch itself from back of face panel. I then separated the 2 elements of the switch.

I took new replacement switch and reinstalled the 2 parts of switch and placed back into hole in face panel. I reinserted the 2 front screws that holds the switch in place. I put the selection knob back on. However, the knob does not fit tightly. The shaft on the switch itself is to long, but the switch works fine. You do not even know that knob sticks out further than before. I plugged unit back into house current and tested range element to see if it works. It did so with no problem. I then replaced rear panels and secured all screws back to their original location and that was all there was to it.

No problem. Was a fast and effective installation.

1. Unplug the power
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

First I found a YouTube video for Maytag Range Repair – How to replace the Surface Element with Limiter - 6" - 1200W

The steps are very easy-
1. Open oven door and locate and remove 2 screws holding top cook surface. These are located near the top inside edge

2. Lift surface cook top and then remove 4 screws holding this section to the cook top. This may require 2 people but I was able to hold the cook top and loosen the 4 screws myself. Then put the cook top aside.

3. Take a photo of the element being replaced for wiring connections.

4. Removing the wiring and element holding clips was very easy. I used needle nose pliers for both

5. The clips have to be removed from the old element and put on the new one. Place them in the same locations

6. Make sure to reconnect the wires to the same pin locations. The replacement element I had the red (hot) wire pin 2b was in
A different location so I had to use the extension wire supplied with the new replacement element

7. Put everything back together in reverse order.

Easy peasy, took me about 40 minutes to complete the entire replacement and have it back in place working.

Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.