66517152K216 Kenmore Dishwasher - Instructions

It is a bit difficult to align the grommet, hose, and mounting arm. Suggest using a little vasoline in bushing for the mounting arm/support. it really helps slide in the arm into that bushing so you can get the grommet and hose lined up.

Also, instead of using the supplied hose clamp, suggest using an automotive style hose clamp if you don't have the special tool for tightening the supplied clamp.

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

When we ordered the part the first time, we pulled the model number from the documentation instead of the machine. We got the wrong part the first time. The people at Parts Select were very knowledgeable and helpful when we called. After we pulled the model number from the machine, they sent the perfect part that popped in with no problems.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

quick and easy replacement, without tools...

i ordered the wrong part and received the new part and credit for the old part, quickly...Plus, I was kept informed with e-mails....

excellent service...

My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet

1. Shut off water valve
2. disconnect water hose(wrench-adjustable)
3. Disconnect drain hose (screwdriver)
4. Pull dishwasher out from under counter
5. Put down towel to soak up residual water that drains out of dishwasher
6. lay dishwasher face down; electronics is located underneath dishwasher.
7. locate faulty drain pump
8. remove electrical connector from drain pump by first pressing on connector retention tab with screwdriver while sliding connector loose.
9. twist drain pump body while using screw driver to depress drain pump retention tab.
10. remove old drain pump body and insert and twist new drain pump body into old location (use screw driver to assist retention tab engagement)
11. attach electrical connector.
12. Return dishwasher to upright position, slide it under the counter (with its cotton cover); reconnect hoses AND turn water supply back on (make sure you remember to turn the water supply back on)

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.

Replaced the pump.That wasn't the problem --- if I had it to start over, I'd pull the drain hoses and run the dishwasher to see what water is flowing where. I had a clogged drain --- and maybe something else. Still working through the details.