66513073K217 Kenmore Dishwasher - Instructions

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!

took the end off and replaced it with the new one

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Very easy to twist off the old pump and replace with new part. Worked perfect after replacement! We just followed you tube instructions

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.

I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

1. Shut off water valve
2. disconnect water hose(wrench-adjustable)
3. Disconnect drain hose (screwdriver)
4. Pull dishwasher out from under counter
5. Put down towel to soak up residual water that drains out of dishwasher
6. lay dishwasher face down; electronics is located underneath dishwasher.
7. locate faulty drain pump
8. remove electrical connector from drain pump by first pressing on connector retention tab with screwdriver while sliding connector loose.
9. twist drain pump body while using screw driver to depress drain pump retention tab.
10. remove old drain pump body and insert and twist new drain pump body into old location (use screw driver to assist retention tab engagement)
11. attach electrical connector.
12. Return dishwasher to upright position, slide it under the counter (with its cotton cover); reconnect hoses AND turn water supply back on (make sure you remember to turn the water supply back on)

easy the sensor was on the right side, and easy to get to, I turn off the power, turned off the water, and pulled it out, the first thing I saw was the yellow wires and plug. took about 5 minutes, to replace it.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.