Back
Back
Keep typing for more specific results...
Models > 59672002015 > Instructions

59672002015 Kenmore Refrigerator - Instructions

All Instructions for the 59672002015
61 - 75 of 493
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both refrigerator door gaskets were brittle & breaking
I ordered a right & left gasket but when they arrived there was no indication of which was the right or left one...so I just had to guess...I easily lifted the old gasket away from the door & removed. Then starting at the top began inserting the portion that goes into the groove with the help of the table knife, continuing down both sides..then sat on a stool to push the bottom section into place...Had to go back over several areas to reseat but finally closed the door to hopefully set the gasket..Drank some hot tea, then removed the left gasket & began the process all over...The extra flaps ended up on the left side of the door so I may have to remove this side and reposition...I'll check it in a few..then will blow all with a warm setting of the low dryer to continue helping the molding process..
Parts Used:
Refrigerator Door Gasket (White)
  • Nancy from ELM CITY, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door To Deli Fresh Broke In Half
Snap Out
Snap In
Yes That Easy!!
Parts Used:
Refrigerator Pantry Lid
  • T.W. from GREENWEL SPGS, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket on the freezer door was worn out causing "snow" to form on the inside of the freezer.
I pulled off the old gasket and placed the new gasket in the existing groove, shut the door; problem solved!
Parts Used:
Door Gasket
  • Judith from WEST CHESTER, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light switch in freezer side got broken
Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Parts Used:
Door Switch
  • Doug from PLEASANT VIEW, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Chaged out Door Light Switch
By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!
Parts Used:
Refrigerator Switch
  • Scott from Kansas City, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The filter was clogged.
Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.
Parts Used:
Refrigerator Water Filter
  • Debbie from Bluffton, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
8 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The toe grille broke when we 1st put it on
We snapped the new one on correctly this time.
Parts Used:
Refrigerator Kickplate Grille
  • Rana from Pittsburg, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Deli Lid Tray broke and was unable to glue back.
Ordered the part. When came in I took it out of the box and slid the two end posts into the provided holes. Lid fixed in less than 5 minutes. Part came in on the third day because I ordered on Friday afternoon.
Parts Used:
Refrigerator Pantry Lid
  • Linda from LOVINGTON, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water supply line to the ice maker kept popping off after I replaced the water filter because an "ice plug" had formed in the fill tube, unbeknownst to me.
1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.
Parts Used:
Refrigerator Ice Maker Fill Tube
  • Michael from TAKOMA PARK, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
icemaker stopped working
Hardest part is access to the icemaker itself. Once I removed the freezer door (bottom drawer freezer), and got the sliding basket out, it was a 10 minute job. Make sure you start the upper screws first, the icemaker will hang there while you adjust, connect the harness, and tighten. Make sure you are ready before you close the door, it will start making ice as soon as the door is closed.
Parts Used:
Refrigerator Ice Maker Assembly
  • Charles from CASTLE ROCK, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Helpful to have instructions
Since there were no instructions, I was a tad hesitant but dove in. I was just replacing the right end cap, not the left. Removed the involved shelf as well as the two drawers above. Undid the three screws involved and carefully removed the slide rail end cap as well as a part in the back that was attached. That was the hairy part. It took a bit of time to remove it since everything seems so brittle but I was careful and got the assembly out without breaking anything. Also had to remove the slide rail and humidity control. Nothing to removing and replacing the slide rail. You just have to put it back correctly oriented. This was easy. I just looked at the one on the left, which I hadn't removed. Most time consuming part was cleaning things that were normally inaccessible, before re-installing.
Parts Used:
Refrigerator Drawer Slide Rail End Cap Set
  • Tim from WINTER PARK, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator would cool for a very short period of time. Then the compressor would shutdown via internal thermal overload or high head pressure. This was caused by the lack of airflow across the condenser coils and compressor.
(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed
Parts Used:
Condenser Fan Motor
  • Daniel from RICHTON, MS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
9 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker stopped making ice automatically
Unplug the electric flat plug from wall. Loosen up 3 mount support screws , Change out unit. Mount Int back onto 3 support screws . Plug in electronic flag plug , It only goes in one way since the plug as a grove on it.
Parts Used:
Refrigerator Ice Maker Assembly
  • Larry from Roosevelt, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Existing icemaker would freeze up, stop making ice.
I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icemaker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.
Parts Used:
Refrigerator Ice Maker Assembly
  • Steve from WAKE FOREST, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator and freezer not cooling
It was easy to replace the start and run capacitors. But did not fix my problem, also replaced the evaporator fan still not fixed. Pulled refrigerator out of RV and ordered a new one.
Parts Used:
Start Relay
  • Tom from FENTON, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 59672002015
61 - 75 of 493