4KPDI620T3 KitchenAid Dishwasher - Instructions

Removed the old axles and rollers and snapped in the new ones. Really easy repair.

Just popped the receiver onto the end of the pipe! I am so glad partselect.com had the part and made my job in finding the part I needed so easy!

First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw that another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.

Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.

Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Followed instructions, those were OK.
Dishwasher front still leaking

I was trying to avoid having to buy a new dishwasher before the holidays. I went on YouTube and found the dirty dishes may mean bad water inlet valve. So, I used my meter to see if the valve was bad and sure enough it was. I ordered the part from Part Select. Once I received the part I removed the old one. Be sure to put a towel down to catch the excess water. The bracket that came with the new prt was a different configuration, but i swapped the new with old and it worked. I addition to the valve being bad the dishwasher upper and lower arms were somewhat clogged. I looked online again and followed YouTube instructions to clean. The dishwasher is cleaning like it is new. I would recommend to anyone doing work on their dishwasher to use part select and thoroughly clean the upper and lower arm.

Warm rollers and holders in warm water for 2 min each slide on all done

Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.

I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.

One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!

Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!

Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.

The hardest thing was getting the old one off and easy snapped the new one on