412101191 General Electric Dishwasher - Instructions

Used drill and easy out to remove broken part, then put in new one

Took off little white plastic pieces at end of rail. Old rack off and new rack on. End pieces in and railing tighten with pliers. Easy!!!

Remove lower panels, turn off hot water supply, Turn off breaker to dishwasher. notice how power connector is orientated and how valve is mounted to chassis of dishwasher and remove Molex connector which supplies power to valve. The power to the valve is 120VAC when the timer gets to the appropiate cycle I measured the valve with no connector attached with DVM set to Diode or ohms setting and got about .825. I measured the NEW part and measure about the same. Have towel under valve hoses for small amount of water will come out. remove small diameter hose , inlet water supply, remove 2 screws holding part with nutdriver to remove valve which exposes the black hose attached to valve. Hose has a hose clamp, use pliers to remove. good time to check and clean hoses. I unwrapped a coat hanger to run through the hoses for debris. to INSTALL reverse the above. clean water away from floor with towel. Turn on hot water supply, check for leaks, I did not have any leaks. Turn on breaker. You can stick a stubby screwdriver into the door close switch of front door which enables you to turn on (swing arm) dishwasher with door open to check water pressure. I have a great deal more water pressure and water from jets spray much higher than before. Old valve was clearly bad, but solenoid of valve still worked, which sucks in the arm when energized. I used a DVM on the 2 wire connector on valve to check for 120vac when cycle turns it on-measured good. I still don't have quite the same cleaning as before. It is 80% better, but something is still not right. My wife put in one of those pot cleaners (red) mesh plastic thingy on top rack--and found pieces of red mesh plastic in debris area, cleaned it out as best I could removing the 2 covers, but not sure valve is opening there or debris is clogged in there which sends pieces of food, etc. through hose to garbage disposal. Hose wasn't clogged. Cleaning better but wife is still saying not as good. The Pump is running good, cleaned dust and dirt out of pump with vacuum. 10 years old, thinking of removing dishwasher from counter and checking the pump area or change it.

I pulled the two clips in the rack guides and pulled out rack and reinstalled the new rack and put the clip back in the rack guides

Thanks for your prompt shipment of the rack I ordered

Just plopped it in, it fit perfectly! I love it! Very easy to order the part, and very fast shipping! I order it and it took a day to get to me!

I pulled the old basket out with my right hand and inserted the new basket with my left hand! HA! Maybe 5 seconds!

Just set it in as it was exactly as described and ordered.

very easy like you said

Had to pull off the front cover where my problem was. Discovered a burnt out switch of some sort, looked it up on your site and found the part. It seemed expensive so I searched a few more sites and discovered you had the cheapest price. I ordered the part on Monday morning and used the cheapest shipping. 5 to 7 days is what i was informed of so i figured it was worth the wait. I got home from work Tuesday and the part was at my door (wow!) I still had my dishwasher torn apart so I put the new part in and about ten minutes later I was washing a load of dishes! I would refer partselect.com to anyone. Thank you! I hope I never need to use your site again but if I do I've got it saved in my computer! (-:

No story just locate partselect.com on internet, select part and order. Part received in a timely manner in great condition. Thanks

The hardest part about this is removing the end caps. I had repaired the wheels a long time ago so I had some idea about how to do it. Bending the back of the end cap very slightly and twisting got them out. Then it was simply a matter of switching the racks, which came with its own wheels, and then putting the end caps back on.

The new rack was somewhat similiar, but the center section that had to be snapped on was different...no spinner on top...thank goodness for the little video on how to take the stoppers off and reinstall them...it worked...thank you for what you have provided the public and me!

I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.

In order to replace the upper dishwasher rack I needed to remove the end stoppers on the sliders. They were difficult to remove and one of them broke. I then ordered new end pieces. The new ones had been redesigned and were very easy to insert. If you need to replace the upper rack be certain to order new endpieces along with the order for a new rack. They are quite inexpensive.

To remove the old upper rack, I needed to use a screw driver to snap out the plastic end stops. That took a little time, because my dishwasher is located in a corner of my counter/cabinets, making the stop on the right very difficult to get to. Once that was done, I just slid the old rack out, the new rack in and replaced the stoppers. I was very impressed with your service and received my order in less time than stated on my order form. Will definitely use you again and recommend you to others!