4070110 General Electric Dishwasher - Instructions

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.

followed the video step by step which was very well expalined and was able to complete the install

The repair was very easy and straight forward. I removed the electrical wires, removed the two hose's and then removed the old valve from the dishwasher frame. To install the new valve, I just did everything in reverse. No problem and I saved about $80 for the repairman to come out and I am sure I would have paid more for the valve if he provided it.

Thank you.

very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.

Opened the package, opened the plastic parts bag, installed the roller and the cap.

Whew!

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!

Had to pull the dishwasher from under the counter to access the water inlet valve. Disconnected the hoses from the inlet assembly. Removed the inlet assembly from the dishwasher frame. Installed the new assembly and reconnected the hoses. Plugged the dishwasher in, selected a cycle to run to check for leaks.

took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down

Three of the four roller of my upper shelf of my dishwasher had broken...I went on line and in ten minutes ordered my rollers....a few days later rollers came and within fifteen minutes my dishwasher was up and running.....thank you so much....I will absolutely use this site again for future repairs....Thanks again. Marlene Martin

Called repairman: announced that the drain pump was gone. Did not seem right. Went to the website. Found what I was looking for. 49% of the time it was a check-valve issue; only 26% of the time was the pump the problem. Took the unit from under the counter; got it on its side; removed the drain pump. Found my first check-valve, but thediagram showed a second lower one toward the sump. Having located both and purchased two valves and and the lower holder piece, I was ready to finish the job. Quarter-inch nut driver and a screw driver and the valves were in and the drain pump re-installed. Most difficult in my case was getting the dw back into its spot and lashed down! Thanks for the good guidance!

Got the part the next day.. opened it and just screwed into place!
Easy as could be. Thank you!!

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found

changed the door gasket no tools,just pulled out the old,lined up the dot (printed on gasket)on the new and started at the top pushed in the new took five minute,the short bottom door seal required a phillips head screwdriver to remove the inside door screws(six screws) the two on the bottom are different they attach to the door hinge and are machine thread the other four are coarse thread.lifted off the panel slide off the old(pay attention to which way the curve goes) slide on the new replaced the panel put in the six screws.the job is done! the door will be tight to close but will be easier after a few uses.