40462051C Frigidaire Range - Instructions

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!

Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Pulled the range out, unplugged it, removed upper back panel, inserted lens through front of control panel, slid the notch on the actual light onto the lip on the back of the plastic lens. Done!

Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.

Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.