36272321001 Kenmore Range - Instructions

slid the old ones out and slid the new ones in. done

The oven would not light and the clock was out. The surface burners worked.

Replaced the stoves control board using the instructions provided on this site. I would just like to add that you should unplug the stove before beginning and also know how to turn off the gas should anything happen while pulling the stove away from the wall to get to the rear to remove the control board.

It was an easy process which took about 30 minutes. A lot of that was cleaning behind the stove. The control board perfectly matched the one on my 1998 stove so I guess it is good for another 20 years.

replaced lights in refrigirator and freezer

I ordered the new control board and installed it, no problem there. I attached the control knob on the new panel and tested the control switch and it would not turn at all. I still have not powered the control panel up at this time. I immediately called back to explain my problem with Parts Select. The person on the phone said that Parts Select will get another panel out to me and give me credit on the defective panel. A few days later I received the control panel replacement and did not install it until I tested the switch. it, too, did not function at all. Both panels seemed to be locked up. I called GE repair center and I find out that this panel is defective straight from the manufacturer and that he has 9 in his truck that are new and they too do not work ! I reported this problem with Parts Select and have been credited on the second panel. I have called GE direct and ordered a new panel and requested that it be tested and approved before shipment. I am now awaiting on the new Panel from GE.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

My grates were all worn and the finish has come off. I took the grates off and put the new ones on. My replacement grates looks awesome. So its still looks worn.

Very was ti replace racks and knobs. Very fast mail service

was still using back burners while waiting for parts (after safety check). I unplugged the electric for the igniters, raised top, installed tubes, checked for leaks with soap solution, closed top, plugged in electric tested burners. Got a big hug and kiss from my wife.

I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

replacement was a snap and took only a small adjustable wrench and a flashlight. asome slight bending of the tube was required, but a gentle hand solved the problem easily.

I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.