3627171892 Kenmore Range - Instructions

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

All I did was remove the old burner and put the other one on. Took less than a minute.

This gas range had an oven that would heat, but it wouldn't hold it at a stable temperature. Say you set it at 300 degrees. Well, it'd head up to broiling temperatures, then drop down to like 200 degrees, then 400 degrees (You get the picture).

My guess was that the thermostat, given that this oven was ~20+ years old, was no longer able to detect correctly the temperature inside the oven.

The thermostat sensor is made up of the housing (The part that sits behind the oven temperature control knob), a long wire (so you can route it to the inside of the oven), and the probe itself (Which I boldly assume is the thing that measures the temperature inside the oven)

TL;DR:

-Pull oven from wall.
-Turn off electric and gas.
-Remove the grates and drip pans off the top.
-Pry the range's cooktop up (It's on like a hinge and is designed to lift up. You have to play with it a bit with like a screwdriver on the sides (One on each side). If you pry just a tad, you'll notice these prongs that act like detents. (LIFT CAREFULLY, the heating elements are still connected via their gas lines! They're flexible, but don't man handle the thing!
-Once that's up, it's time to finally start removing the thermostat which is the knob that controls the oven temperature. Pull the plastic knob off which will expose the two screws you need to detach it from the oven (Phillips head). Be super careful. You don't want to drop these screws. You'll be struggling to fish them out of the empty space that sits between the thermostat and plastic knob.
-Once that's loose, open the oven door and detach the thermostat from the back of the oven. Recycle the prongs holding the old thermostat sensor for the new one.
-Go to the back of the range. Like the actual back part of it.
-Frustrate yourself with pulling out the thermostat through the route it's been put in. It's difficult to route it through the tight spaces, but not complicated. Keep a mental note of this route and copy it with the new thermostat that you have to install.
-Don't fret, when it comes time to wire the new thermostat sensor, it's actually a lot easier than you would think to find that little hole in the back of the range that you have to slot it through. It's just slightly covered by insulation. Pulling it slightly aside, you'll see it very easily.
-Screw in the thermostat housing at the front of the oven.
-Frustrate yourself again by routing the wire while taking care not to bend the probe (This is my assumption not to bend it and I think it's a safe assumption to make)
-Find that tiny little hold in the back of the range again, insert the probe through it, then use those recycled prongs to hook that probe into place.
-Yay, you're almost done.
-Reinsert knob on thermostat.
-Turn gas and electricity back on.
-Give it a test run to see if you did it right.
-if it still doesn't work, then it might not have been the thermostat giving you problems.
-If it does work, put everything back the way it was.
-You're done.

Followed you tube instructions I found on line via parts select recommendations.

Just lifted off the old burners set on the new ones.

Simply took out old burners replaced them with new burners, no tools needed.

I put it in the same way tuck it out

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Go to utube videos for this are there

Simply removed old burners. Placed leveling nuts in place. Replaced new burners in place.

They turned out to be 1/4 inch hex head screws. Only after soaking with penetrating oil could we budge them. There must be a special tool to loosen them on the back side where there is no room to get a socket on them and since they are in the heated part of the oven they are almost welded in. We were successful, but could only get one screw back in. So never use your oven with the door left open as I did if you do not want to repeat what happened to me.

Straight forward as per instructions. Removed old igniter, replaced and tested new one and it worked. However, the gas oven would not turn of. Valve may be defective. Knob control is not stripped and turned to full stop. Troubleshooting continues. Part(s) and instructions worked perfectly.

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

My husband and I probably could have done the repair in 15 minutes except for the difficulty lifting up the range top, dropping the screws into the range where they could not be retreived, threading the thermostate into the little holes from the top to the inside of the oven and then trying to hook the range top back into place. Even with all the difficulties we still accomplished the task in one hour. Thank goodness we had 4 extra screws that worked (actually only takes 2 but of the 6 we had, 4 fell into a place you could not reach into). Glue on the end of the screw driver finally kept the screws from falling into the black hole. It was an adventure and would do it again.

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.