11060522900 Kenmore Dryer - Instructions

First I removed the two wires from the overheat fuse, then I removed the 1 screw and removed the fuse. I installed the new overheat fuse and attached with 1 screw, then reconnected the 2 wires. I attached the back cover with two screws and tested the dryer. It was working, so I finished attaching the back with the remaining screws and exhaust duct. Installation complete.
Note: Two weeks later I had to replace the fuse again because I had checked the duct pipe and exhaust chute, but not the bottom at the fan. Be sure to remove the flat exhaust duct and check for bulid-up at the bottom under the fan.

checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your website and the promt efficient service

First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Piece of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!

Removed back cover, removed broken switch, replaced with new switch, replaced back cover, told wife her dryer was fixed.

After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.

I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.

The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.

Once I unpluged the dryer and then removed the back cover, I located the heating unit and then removed the thermostat. Once that was done, I installed the new thermostat and connected the wires. I tested the dryer to make sure that it would heat. Then I replaced the back cover.

Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....

installed the new dryer lint screen, it fit perfectly
and is now in operation.

Purchased thermal cut off kit but only replaced the top most thermostat. There were some extra wires wired into the bottom thermostat, that were not described on the video or any other repair user posts. It checked fine on my multimeter anyway.

I watched the installation video on both parts before I purchased them and it was a piece-of-cake after that.

1. Shut off gas and disconnected dryer.
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap.
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...

Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.