11027272600 Kenmore Washer - Instructions

Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.

1. Unplug the machine.
2. Turn the water off.
3. Disconnect the supply and discharge hoses.
4. Open the cover and remove the cap/cover of the agitator. Use socket wrench to remove the bolt securing the agitator. Pull up on the agitator and remove it.
5. Lay washing machine down on it's front. Remove the inlet and outlet drain hoses from the discharge pump.
6. Remove the 2 "faston" connectors from the motor start capacitor (looks like a D cell flashlight battery). Rock the connectors back and forth and pull gently until they come off. Polarity doesn't matter but to be safe make note of the positions.
7. Press the release clip on the motor connector and pull to disconnect it. Move the wiring harness out of harms way.
8. Remove the 3 bolt securing the motor and transmission assembly to the bottom of the tub. Pull the drive assembly out of the machine and place it on a suitable work surface.
9. Examine the tub brake assembly (still on the bottom of the tub), the clutch assembly (on the motor/transmission assembly you just removed and everything else for wear or damage. Now if you decide to proceed with repair continue with the following steps. If not you're done.
10. Remove the inverted cup washer from the agitator shaft of the assembly. Remove the "U" clip from the shaft and remove the clutch mechanism from the drive assembly. Make a sketch of the position of each of the removed components to aid in reassembly.
11. Now you can see the gear case cover and it's seal. If it is leaking (as mine was) you will need to replace it.
12. With the assembly level remove the bolts around the cover and remove the cover. Place the cover on a flat surface and with a screwdriver or punch drive the old seal out of the cover from the outside in.
13. Clean the seal area and check for damage. Clean the cover and transmission housing surfaces of old gasket material. There is a factory sealant available for reassembly but I chose an automotive RTF @ $4 vs $24 and it worked OK.
14. Installing the seal requires some tools and experience to done successfully. The right size sockets or piece of pipe, coupled with an arbor press or vise will get the seal in. The cover is delicate so if in doubt find a machine shop.
15. Support the outside of the cover on a hard surface and with a socket or short pipe length, PRESS (don't hammer) the new seal into the gear case cover.
16. Make sure there is lubricant in the gear case. Not overflowing but maybe 1/2 full when view with cover off on a level surface.
17. Apply some RTV sealant to trhe cover and install it. Tighten bolts evenly. Light torque (1-2 ft-lb).
18. Reassemble washing machine and test for leaks and proper operation.

turned the washer on it's back and shoved the tub to the side to release pressure on a spring ,pulled it loose and installed new one. this worked for the back two then turned washer on it;s face and repeted the process on the front spring.
Washer works great now.

popped thecap off removed the bolt, pulled agitator off replaced cogs(dogs) then put back together. works like new.whole time took about 10-15 min. saved my self 150.00 by not hireing repair man.

remove 2 screws that hold timer section
remove large clips that hold lid section
repace lid swich and put back together
works good

First off I would highly recommend the review by Dennis From Evans City PA. This was quite helpful.

The problem is the lid switch assembly is glued together and the original part came apart and needed to be replaced. The symptoms described by others were accurate so we opted to replace it.

On my machine there are two screw on the front corners of the panel where the dials attach to the top of the washing machine. I removed those two screws and by lifting up and forward was able to move the whole thing out of the way.

You should see the connection from the dial panel running down into the wash basin. This is where you will unplug the old switch and replace it with a new one. There are little plastic clips that hold it in place, but you can squeeze them with your fingers to remove it from the panel.

In order to get access to the underside where the wires are connected you will need to remove two clips that hold the back pane to the rest of the sheet metal. In my case I wasn't quite prepared for the entire frame to move but once the clips are removed the back panel is completely removed and you can pull it forward to gain access to the underside.

Once you are able to get underneath you will see a screw that holds the ground wire. This is the one that you may need pliers to remove. There are two screws that hold the switch in place but you can access them at any time. I had already removed the old screws by this point. This should leave the switch disconnected from everything and you can install the new one.

Now just connect everything back together. The two screws for switch where the lid hits. Connect the ground wire and run the the connection back to the top portion where it will connect back up to the top panel.

I would add that there are two thin plastic strips that ran vertically up the back fo the back panel that meet the outer casing. I had to re-seat these before putting the clips back on the top.

Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remove black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...

Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.

Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done! Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!

Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

i knew the lid sw. must be bad and had a new one in hand, but when i remove the sw. ( near the lid ) i found the wires going back to where i could not reach. was not sure how to get at them so i repaired the sw. with tape untill i could find how to get at the wire end. after reading more in this repair area i know that i need to remove the control panel which is easy to do. next time i will read all i can on repairs in this section!!

After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!

Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.