10646 - Instructions

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

I took a 1/4 nut driver and removed the wire cover. I then used a small screwdriver to push up the clips the lock the unit in place. I then unplugged the unit and removed. I then used the same nut driver and removed the bottom plastic cover and installed it on the new icemaker. I then put the new unit part way back onto it slides, being carful to make sure the water fill spout clears the unit. Next I plugged in the wire harness and then slid the unit the rest of the way in until it locked in place. I then reinstalled the wire cover.
This unit was delivered at 1:30 and it was installed by 2

First I removed the cutter grid assembly by removing two screws. Also disconnect the wire that powers the grid. Once on the bench, simply remove the broken cutter wire. String in the new wire, starting at one end and working back and forth to the other end. Tighten the terminal screw on the first end, and then "strum" the wires, one at a times, pulling the wires taught. Pull the excess wire thru the second terminal, until all wires are taught, with equal tension. Tighten the second terminal screw, and cut off excess wire at both ends. Re-assemble cutter grid into Ice Maker.
Problem solved!

In pre-replacement of the circulation pump, i had read a story about how to make sure you cover the drain hole to prevent hardware from falling down it. Well I followed the instructions in doing so by covering the hole with a paper towel. After removing the pump i noticed some build up behind it. So like any other person i cleaned it up, and i just happened to use the paper towel covering the hole. Im sure you know what im going to tell you next. When replacing the pump i dropped a screw and yes down the drain it went. After a few laughs between my boss and I, I had to share this. When you block the drain with something leave it THERE until the job is done.

Repair was easy and producing ice within five hours.

Removed nuts and bolts in order to remove ice maker unit, and 4 screws from the surrounding shell to get to said icemaker unit. I'd say it was a 15 minute job, but that's kind of a lie. It took me about a week of procrastination. And then 15 minutes to remove one unit and then put in the new unit. It's very easy unless you're really lazy. In which case it's still easy, the hard part is getting outta your recliner.

Easy as pie, I followed the directions on the box that the replacement filter came in, and installed it and the cap simply and easily.

I removed the cutter cover in the front of the ice maker (3 screws), than removed the circulating pump cover (1 screw). Remove the drain tube from the cover before removing the cover from the icemanker. The drain tube is removed by pulling straight down and twisting. Remove the circulating pump, utilizing the 4 inch extension (3 screws). Reinstalled all in reverse.

Note: install a plug in the drain hole in the bottom of the ice maker (paper towel etc). I dropped a screw on the installation and it fell in the drain hole. It did not impede the drain flow. It has now found a new home.

PartSelect was fantastic and I would recommend them to anyone! Online, Sears only showed a parts breakdown so I went to the service center. They could sell me an ice maker but PartSelect had the same ice maker for $35 less and it was on my door step the very next day! Mu husband plugged it in an we were on our way. You have been very easy to work with. I was amazed at the delivery time and I will use you in the future!

First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)

Once I had the unit completely out of the freezer the replacement part took only minutes to replace.

Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.

Simple repair - well worth the effort.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

Ice Maker quit working. Seemed like a water supply issue but when I read the other reviews, I decided to install and see. bolted the bracket on with three screws, slid in place. Nothing happened and about 10 minutes later, I heard the water release to the ise maker and have been making ice ever since.