Gibson Washer Seals and Gaskets

Your Price

$49.95

PartSelect Number PS474458

Manufacturer Part Number 5308027429

This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before applying the adhesive, ensure that the area is completely clean from any debris and is dry. You may wish to use small clamps to hold the material in place while it dries. If the felt has come loose or broken apart, this may cause your dryer to make loud noise, indicating that new felt or rubber needs to be glued into place. Use gloves to apply glue.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Gerald from Alliance, NE

Burned out heater element

1.Remove 2 screws and the air intake grill on the back of the unit. remove the drive belt. 2. Remove 2 screws on rear of top, slide top back and remove. 3. Remove 2 screws about a foot down on the inside on each side of the front cover. Remove four screws that secure the plastic control panel and the front panel that are right behind the control panel on the top. Disconnect the wiring harnesses, cut the nylon wire tie that is closest to the front cover. 3. lay unit on its back and and remove the two screws on the lower edge of the front panel, take your putty knife and slide it in the gap between the front panel and the dryer cabinet and release the two spring clips on both sides. Then you can lift off the front panel and control panel, set it to the side. 4. Remove the screw and the nylon guide from the center of the top front case crossmember. Remove the three screws on the inside rear of the drum, lift out the drum and set aside. 5. The drum pivot just sits in a nylon socket, pop it toward the top of the machine and lift it out, you may want to clean it good and re-lubricate it on reassembly. Disconnect the wires from the heating element and the heat sensor. 6. Set the cabinet upright and remove the four screws on the back side of the rear of the cabinet but not the two that are right in the center, they hold the pivot fixture and don't need to come out. The heater coil pan is now loose and ready for removal. 7. The seal between the filter housing and the blower housing was torn and this is an important part to have right, any air leak here will do the same thing as a dirty lint filter or plugged dryer exhaust and your new heating element will have a short, hot life. I pulled the old one off, scrapped the old glue off, applied the adhesive like the instructions on the tube say and after a few minutes installed the new seal then set the front panel to the side to let the adhesive dry. 8. The reassembly is just the reverse of the disassembly , use a couple nails or awls to help hold the dryer heater pan in place for screw installation and you might want to gentle squeeze the wire connecters if they feel loose, also check for clogged or kinked exhaust and stress the importance of cleaning the lint filter after EVERY load, it is small and all the air that cools the heating element must go through it, if is isn't maintained your new element won't last long. Have fun! Read more...

Videos!

Your Price

$98.89

Gibson Washer Bellow With Clamp

PartSelect Number PS900237

Manufacturer Part Number 5303937187

Also known as the door boot seal. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.

Fixes these symptoms

Leaking
Marks left on clothes
See more...

Installation Instructions

Durr from Mulino, OR

The rubber boot on our front loading washing mashine was torn and needed replacing to stop the leaking water.

The instructions were good, but putting the spring on was quite difficult. The 3 spacers that came with the boot didn't want to stay in place. Finally I got 2 c clamps, putting a clamp over the spring and rubber spacer, and that did the trick. without the c clamps it would have been extremely difficult to get that spring on. Now it's fixed and no more leaks. Read more...

Your Price

$57.95

Gibson Washer O-ring/gasket

★★★★★

1 Review

PartSelect Number PS724852

Manufacturer Part Number 134146100

This part is between the front and rear outer tubs.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Timothy from Biglerville, PA

Spider was corroded and broke from being weakened by the corrosion

Removed the entire front cover of the washing machine and dicoonected the springs that support the tub. Left the tub down and disconnected the struts and unhooked all the wiring and pulled complete tub out of machine. Removed all the bolts around the tub shell and split the tub shell. Remover the motor from the sheel to make it lighter to work on, removed the pulley on the drum shaft and pulled the drum out of the shell. Found that the cast alluminum spider was weakened by corrosion and this caused the spider to break. The spider itself should be able to be purchased seperately because the stainless steel drum was okay and could have been reused. The biggets problem I had was getting the tub back in the washing machine and getting it suspended by the springs again. I used a 6 x6 block and a 2 x 6 board to lift the tub up in the air to get the tub springs hooked back up. This took 2 people to accomplished. After the tub was suspended on the springs the rest was easy. Read more...

Your Price

$29.95

Gibson Washer Splash Cover Seal

PartSelect Number PS418992

Manufacturer Part Number 131901400

The tub ring seal or splash cover seal is used for washers. This part seals the tub cover to the outer one and prevents water leakage from around the tub ring. If your seal is damaged and you are experiencing water leakage, it is best to replace this part. Refer to the manual provided by the manufacturer for further installation instructions. Remember to unplug your washer from the power source before starting this installation process.

Fixes these symptoms

Leaking
See more...

Your Price

$15.95

Gibson Washer Seal

PartSelect Number PS454140

Manufacturer Part Number 5303161173

Your Price

$29.95

Gibson Washer Upper Lip Seal

PartSelect Number PS454174

Manufacturer Part Number 5303161307

This basket drive tube seal or upper lip seal is used for a top washer and is located on top of the transmission, below the agitator drive block. The tube seal functions as a protective tool to prevent water from leaking into the drive tube. The measurements for this seal are: 4 inches in length, 1 inch in height, and 0.01 lbs in weight. Remember to unplug your washer from the power source before beginning this installation, as a safety precaution. For installation instructions and accurate guidance, refer to the manual provided by the manufacturer.