Whirlpool Washer Dryer Combo Wire Plugs and Connectors

Videos!

Your Price

$18.95

Whirlpool Washer Dryer Combo Washer Drive Block 2 5/16 High

★★★★★

2 Reviews

PartSelect Number PS11741977

Manufacturer Part Number WP389140

This part is for large capacity belt drive and direct drive appliances.

Fixes these symptoms

Leaking
Spins slowly
Will not agitate
See more...

Installation Instructions

Dexter from Milwaukie, OR

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose

After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...

Your Price

$18.95

Whirlpool Washer Dryer Combo Dryer Terminal Block

★★★★★

1 Review

PartSelect Number PS11741489

Manufacturer Part Number WP3397659

This part is an electrical connector where you can attach wires. This part does NOT included the wires, screws, and nuts. Must be order separately

Installation Instructions

DAVID from LEESBURG, FL

One of the power cord connections on the terminal block was loose. Screw on terminal block was cross threaded when installed. Took six years to smoke the wire.

Removed and replaced terminal block, power cord and black wire to timer. Read more...

Your Price

$52.45

Whirlpool Washer Dryer Combo Terminal And Wire Kit

PartSelect Number PS334181

Manufacturer Part Number 279318

Your Price

$18.95

Whirlpool Washer Dryer Combo 3-circuit T.p.a. Connector Plug

★★★★★

2 Reviews

PartSelect Number PS11741226

Manufacturer Part Number WP3360056

Fixes these symptoms

Burning smell
Will Not Start
See more...

Your Price

$9.95

Whirlpool Washer Dryer Combo Washer Burner Box

PartSelect Number PS11743322

Manufacturer Part Number WP62889

Your Price

$79.77

Whirlpool Washer Dryer Combo Wiring Harness

★★★★★

1 Review

PartSelect Number PS11751764

Manufacturer Part Number WPW10278751

Introducing the genuine OEM HARNS-WIRE from Whirlpool. Specially designed for optimal performance in a variety of well-known Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models, enhancing the overall usability of the device. This Wiring Harness plays a pivotal role in connecting electrical components to the power source in laundry centers, facilitating a smooth and efficient operation. To ensure the safe installation of this part, it is recommended to unplug the laundry center beforehand and wear work gloves to protect your hands. While parts may appear similar, please keep in mind that size and shapes can have minor variations. Ensure your model compatibility with the HARNS-WIRE for best results.