Washer Dryer Combo Ducts and Vents

Your Price

$10.45

PartSelect Number PS3535020

Manufacturer Part Number MCQ41502701

This is a pump bracket damper for models of LG washing machines. This damper is used to protect the pump within the washer from excessive vibration damage during the washing cycle. If your washing machine is vibrating or making an excessive amount of noise during the cycle, these dampers could be worn out and in need of replacement. This damper is made of rubber and measures approximately 1 inch long and 1 inch wide. Replacing this damper will require you to access the underside of the washer, or wherever the pump location is for your model. This OEM damper is sold individually, and most washers use 2-3 of these dampers for the pump bracket, so consider how many you need before ordering.

Your Price

$13.75

Washer Dryer Combo Damper

PartSelect Number PS8752496

Manufacturer Part Number MCQ62786001

This is a rubber bumper made for LG dryers. This bumper is installed on the inside of the dryer door to ensure the metal door does not bend or get damaged when you close it, and ensures a barrier is between the two pieces of metal when the dryer is spinning quickly. To replace this bumper, you will need a Philips-head screwdriver or drill bit. This bumper is a genuine OEM part and is sold individually, so if your dryer door requires multiple bumpers, consider that before ordering.

Your Price

$102.36

Washer Dryer Combo Heat Duct Assembly

★★★★★

1 Review

PartSelect Number PS3526481

Manufacturer Part Number 5209EL1001E

Fixes these symptoms

Marks left on clothes
See more...

Videos!

Your Price

$78.95

Washer Dryer Combo Side Venting Kit

★★★★★

6 Reviews

PartSelect Number PS3575086

Manufacturer Part Number 3911EZ9131X

This dryer side vent kit lets you vent the exhaust to the side or bottom of your dryer instead of the default rear position. Included in the kit are 2 straight aluminum foil outlet ducts, each 4 inches wide, along with 1 duct elbow, 1 cover plate, 1 screw, and an instruction sheet. This is helpful for flexible installation in areas where rear venting is not possible or practical. All parts are genuine replacements from their original manufacturer.

Installation Instructions

ROBERT from DAWSONVILLE, GA

Install aftermarket side vent kit

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came. Read more...

Your Price

$67.87

Washer Dryer Combo Dryer Exhaust Duct Kit

★★★★★

2 Reviews

PartSelect Number PS3633049

Manufacturer Part Number W10470674

This kit is used for the bottom and side exhaust. The kit includes both the straight and elbow vent.

Installation Instructions

Mark from San Diego, CA

Needed to change rear exhaust to the side to fit dryer into my closet.

First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer. Read more...

Your Price

$27.95

Washer Dryer Combo Damper(120n)

PartSelect Number PS12726782

Manufacturer Part Number WH16X28408

Your Price

$74.20

Washer Dryer Combo Blower Housing Rear

PartSelect Number PS8689122

Manufacturer Part Number 137551800

Your Price

$134.37

Washer Dryer Combo Duct-air

PartSelect Number PS11741422

Manufacturer Part Number WP3387911

Introducing the DUCT-AIR from the trusted brand Whirlpool. This is a genuine OEM piece that is designed to work compatibly with selected models of Whirlpool appliances. Key to your appliance's functionality, this DUCT-AIR facilitates the flow of warm air from the heater to the back of the dryer and into the drum, assuring efficient operation. Remember to unplug the dryer while installing this part and wear work gloves to ensure hand safety. This mastery engineered part is sure to be the exact fit you need, just be sure to verify its compatibility with your model before ordering. Choose Whirlpool for trusted, high-quality parts.

Installation Instructions

Thomas from Edgartown, MA

Screen on the hot air vent disintegrated

It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones. Read more...