Troy-Bilt Lawn Tractor Bearings

Your Price

$9.89

Troy-Bilt Lawn Tractor Snow Blower Hex Flange Bearing

PartSelect Number PS9178250

Manufacturer Part Number 941-0245

Used mainly in snow blowers, this flange bearing is typically installed on the axle and creates a tight fit with little friction while still allowing for movement.?Your equipment will likely feature multiple of these bearings, so refer to any diagrams for your model to determine whether you will need one, or more. This is an OEM part that is sold as an individual item and has a 0.75-inch inner-diameter, 1-inch outer-diameter, and 1-inch height.

Your Price

$5.95

Troy-Bilt Lawn Tractor Lawn Mower Flange Bearing

PartSelect Number PS9122043

Manufacturer Part Number 741-0660A

This OEM-manufactured flange bearing supports and enables the smooth rotation of parts in your lawn equipment, such as the blade assembly, axle assembly, or steering components. This bearing has an inner diameter of .76 inches, an outer diameter of .941 inches, and a width of 1 inch. It is made of plastic. A similar similar style flange bearing can be used at the bottom of the crank, but it would be made of metal. When the bearing is broken, you may notice signs of wear and abnormal squealing noises coming from your machine. If neglected, the parts the bearing is supporting can overheat and potentially seize up. To switch out a flange bearing, you need to take off any bolts, screws, or clips that are holding it in place. Using a hammer or a bearing puller tool, gently push the bearing out of its housing. Since this part is sold individually, remember to refer to your user manual to understand how many bearings your machine will need. It is strongly recommended that you replace all the bearings in one go, as they wear out at the same rate.

Your Price

$6.50

Troy-Bilt Lawn Tractor Lawn Mower Flange Bearing

PartSelect Number PS9112939

Manufacturer Part Number 741-0516B

Your Price

$5.40

Troy-Bilt Lawn Tractor Lawn Mower Hex Flange Bearing

PartSelect Number PS9311603

Manufacturer Part Number 941-0656A

Installation Instructions

Patrick from Northville, NY

Yardman / MTD wouldn't steer left, makes a popping and grinding noise when turning.

To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had to do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt. Read more...

Your Price

$7.91

Troy-Bilt Lawn Tractor Lawn Mower Plastic Flange Bearing

★★★★★

1 Review

PartSelect Number PS9302372

Manufacturer Part Number 741-0487C

Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect while moving smoothly and freely and is sold individually. When this part malfunctions, you may notice the shaft becomes very sloppy or comes disconnected. To complete this repair, you will need a screwdriver, a socket set, and pliers. Customers rate this repair as Medium difficulty.