Simplicity Parts

Simplicity Lawn Mower Spark Plug

★★★★★

★★★★★

1 Review

This part is the replacement spark plug for your engine. It measures approximately 2.5 inches by 1 inch. The spark plug creates the spark that ignites fuel in your engine during the combustion process. Over time, spark plugs can become worn and can go bad, which will prevent the engine from firing. You can test your spark plug for continuity with a multimeter, and inspect it for corrosion if you suspect the spark plug has gone bad. This is an OEM part sourced directly from the manufacturer and it is sold individually.

Simplicity Engine Oil Seal

★★★★★

★★★★★

1 Review

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. Refer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

Simplicity Fuel Filter This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. If broken, there may be a leak or blockage and the part should be replaced. The part may also need to be replaced according to manufacturer's specifications, and is a manufacturer-approved part. Refer to your make, model and diagrams to ensure this part is correct.

Simplicity Engine Filter This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

Simplicity Hex L-nut

Simplicity Lawn Mower Roller Designed for use in Snapper and Simplicity ride-on mowers, this Roller is sourced directly from the manufacturer, is made of durable black plastic, is 4 inches long, and sold individually. The Roller helps allow the deck to move over the lawn without gouging into the ground. When the Roller has broken, you will notice the deck starts to ground out. This part will wear over time and needs to be replaced if it is damaged or fatigued. Customers rate the difficulty of this repair as Medium.

Simplicity Lawn Mower Nut Push

Simplicity Snow Blower Shear Pin Shear Pins are designed to break off in order to prevent further damage to your machine. Because they are designed to break, we recommend having a few spares on hand. This part is made of metal, is silver, is not part of a kit or assembly, and is sold individually. A Shear Pin will break when you hit a large chunk or ice or other debris. Once it is broken, it will need to be replaced. You will need pliers to complete this repair. Customers rate this repair as Easy.

Simplicity Suspension Bushing

Simplicity Lawn Mower Ball Bearing This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lubricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.