Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Gas igniter glows | but will not light | Will Not Start
This part works with the following products:
Range, Cooktop.
Part# WP8273062 replaces these:
AP6012356, 7101P606-60, 74009337, 8273062
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.7
Filter By Rating:
5 Stars
2
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Kenneth G - February 28, 2018
Verified Purchase
Stove burner igniter
Just the right part, just in time.
★★★★★
★★★★★
Allen E - January 20, 2022
Verified Purchase
Perfect fit
Head stripped off original and this part was a perfect fit after the old screw was extracted.
★★★★★
★★★★★
Jeff V - April 22, 2019
Verified Purchase
Perfect replacement parts
The burner igniter and mounting screw were indeed the perfect replacement parts.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.5 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Whirlpool gas stove burner igniter had broken.
Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat.
... Read more I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.
The ceramic on the electrode broke due to water over boiling the week of Thanksgiving. When i tried to loosen the screw to replace the electrode it broke off inside the threads. Ordered whole new unit overnight. Back in business in five minutes. Thanksgiving was back on!! Thanks!
- Removed the cover. - Removed te two Torx screws. - Pulled the burner a couple of inches to be able to disconnect the wire. - Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head. - Treated all screws with a hi
... Read moregh temperature copper paste to prevent oxidation. Installed the new ignitor with the new screw. - Reconnected the wire. - Installed the two Torx screws. - Voila, it works.
two igniters didnt function and it continued to spark after the gas ignited.
Well, after I finally got the parts, the repair was easier than anticipated. You deffinitely want to lift the unit out to replace the spark module and swap over one wire at a time so you dont forget where they go, (important on a gas stove) When I pulled out the old unit I found it was just jammed in there when constructed, I expected mo
... Read morere from Jenn-air, and the plastic casing was broke and pulled apart. Surprised it lasted this long. Also three of the ceramic insulators on the ignitors were broke or cracked. But over all the unit was fairly simple to repair if you take your time and practice safety. Remember, you are working with gas and electicity, and use soapy water to check your connection when you reconnect the gas line. Dont try to work on it still hooked up and in its mount . Disconnect it and lift it out.
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Frank
July 30, 2019
All ingitors do not stop sparking when plugged in. They will only stop after extra large burner flames on, ignitors do npt stop with any of the others burners flamed on.
For model number JGD8430
Hi Frank, unplug the appliance and give it time to dry out. Plug the model back in and if it still is sparking then you may have to replace the igniters. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
John
December 5, 2019
My burners aren’t sparking when trying to turn them on.
For model number WFG770H0FZ0
Hello John, thank you for writing. This sounds like a faulty Spark Module, part number PS11755330 for your model range. Good luck with your repair!
Was this helpful?
Thank you for voting!
Mary
October 14, 2022
WHAT PART NUMBER DO I NEED FOR THE FOUR SPARK IGNIGTORS ELECTRODES ON MY JENN-AIR GAS STOVE TOP SURFACE THE BURNERS serial #DY3415472 and THE BROIL/BAKE IGN ITOR THE OVEN?
For model number JGS9900CDS00
Hello Mary, thank you for your question. The Spark Igniters are the same part for the four burners on top. The part number is PS11744318. The Bake Igniter is part PS11744546 and the Broil Igniter is part PS11723189. We look forward to hearing from you.
Hi Cynthia, thank you for asking, The oven igniter, part number PS12348439, fits your model. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
