YWET4027HW0 Whirlpool Washer Dryer Combo - Overview
Sections of the YWET4027HW0
[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Dryer Thermal Fuse
PartSelect #: PS11741460
Manufacturer #: WP3392519
The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. If the fuse ...
$17.95
In Stock
Agitator Directional Cogs
PartSelect #: PS388034
Manufacturer #: 80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your wa...
$7.31
In Stock
Dryer Internal-Bias Thermostat
PartSelect #: PS11741405
Manufacturer #: WP3387134
This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heate...
$27.25
In Stock
Dryer 3 Wire Door Switch
PartSelect #: PS11741701
Manufacturer #: WP3406107
This dryer door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open, and operates the drum light. White in color and 6.5 inches long, this OEM swit...
$27.27
In Stock
Dryer Rear Drum Support Roller Kit
PartSelect #: PS347627
Manufacturer #: 349241T
The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings, and one palnut (or retaining washer). The kit does n...
$17.78
In Stock
Dryer Idler Pulley
PartSelect #: PS334244
Manufacturer #: 279640
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
$25.95
In Stock
Multi Rib Belt
PartSelect #: PS382430
Manufacturer #: 661570
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium"...
$24.11
In Stock
Dryer Thermal Cutoff Kit
PartSelect #: PS334278
Manufacturer #: 279769
This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.
$34.95
In Stock
Dryer Tri Ring
PartSelect #: PS11755850
Manufacturer #: WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$10.95
In Stock
Washer Agitator Cam Kit
PartSelect #: PS334648
Manufacturer #: 285809
This kit included the cam, 4 dogs and bearing.
$13.95
In Stock
Washer Inner Cap Seal
PartSelect #: PS11748108
Manufacturer #: WPW10072840
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollabl...
$10.45
In Stock
Dryer Heating Element Wire Kit
PartSelect #: PS334206
Manufacturer #: 279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
$9.95
In Stock
Questions And Answers for YWET4027HW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roberto
January 17, 2023
THE WASHER FILLS WITH WATER AND DRAINS , JUST DRAINS NO SPIN?
What part do i need?
For model number YWET4027HW0
Hello Roberto, thank you for contacting us. We would recommend checking the following parts: the drive belt, part number PS11747978, the drive pulley, part number PS10057144, the shift actuator, part number PS11769864, and the drive block, part number PS11741977. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Was this helpful?
Thank you for voting!
Related Parts:
Washer Drive Pulley
$37.76
In Stock
Washer Drive Block 2 5/16 High
$18.95
In Stock
Washer Drive Belt
$28.33
In Stock
6 Pin Shift Actuator
$49.32
In Stock
Shawn
April 26, 2023
Hi, the washer stops and then won’t drain
For model number YWET4027HW0
Hello Shawn, thank you for contacting us. Based on our research, the issue is most probably with the defective Drain Water Pump, part number PS11770076. You may need to check the drain water pump to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Water Pump
$140.50
In Stock
Malcom
January 7, 2025
I have power to mother board but nothing on washer works dryer works fine
For model number YWET4027HW0
Hello Malcom, thank you for your question. You will need to test the Electronic Control Board PS12723951 and the board wiring Harness PS12346520. If you need to know how to test, please view this video. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
HARNS-WIRE
$75.56
Special Order
CNTRL-ELEC
$204.99
In Stock
- < Prev
- 1
- Next >
Common Symptoms of the YWET4027HW0
[Viewing 27 of 27]Will not agitate
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Running With Door Open
Fixed by
these parts
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Door Pops Open
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Cycle Not Advancing
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Light not working
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Heat stays on after drum has stopped
Fixed by
these parts
these parts
Show All
Timer Not Working
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was working, but no heat.
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of ... Read more needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of ... Read more needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.
Read less
Parts Used:
-
ANTHONY from CHESHIRE, CT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
3034 of 3440 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door switch was bad
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service
Parts Used:
-
pat from lisbon,, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
1028 of 1085 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the a ... Read more gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Slip the new cogs into the underside of the cup, and slide the cup back down in the a ... Read more gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Read less
Parts Used:
-
mike from Kent, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
943 of 1036 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!