Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair o...
Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is imp...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature or amount of water needed.
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
Ask our experts a question about this model and we'll get back to you as soon as possible!
10 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Phil
February 25, 2020
What is code f-01
For model number WFW8300SW02
Hello and thank you for writing.
The whirlpool washer error F01 means there is a communication error in the EEPROM circuit of the main control board, in other words, the mainboard cannot access or read/write to its memory chip.
We suggest to try a hard reset:
Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should hopefully clear this problem. We hope this information helps. Please contact us anytime if you require further assistance.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jens
September 13, 2023
I am looking for a control board for a whirlpool duet washing machine model number WFW7300SW02.
Thank you,
For model number WFW8300SW02
Hi Jens, thank you for contacting us. The control board compatible with your model is part number PS11755952. It manages the washer's functions such as filling, washing, draining and spinning. We hope that helps!
I’m having a problem with the drive belt fraying and breaking. Replaced it and 4-washes later the new one frayed and came off the pulley. Any advice or tip are appreciated.
For model number WFW8300SW02
Hi Robert, thank you for contacting us. According to our research, the issue is probably with the Motor Pulley, part number PS11746256. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
What is production year for serial number HLU1027126?
For model number WFW8300SW02
Hello Chon, thank you for your inquiry. According to our research, your unit was manufactured in March 2007. We hope this information is useful!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Roger
May 6, 2023
Code f25 apparait , est ce que je peux le réparer moi-même, c’est à mon chalet
For model number WFW8300SW02
Hello Roger, thank you for your question. The F25 error is a problem with the washer motor's tachometer. This makes the board unable to determine the spin speed of the motor. We recommend checking the motor control board PS11750132, the main control board PS11755952, or associate wiring such as Motor harness PS2329214 and Electrical Harness PS11749466.
Good luck with this repair.
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find
... Read moreanything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.
