Parts That Fix Whirlpool Dishwasher WDTA50SAHZ0 Not cleaning dishes properly

This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.

This authentic Dishwasher Upper Rack Adjuster Kit with white wheels is a kit made up of primarily plastic and metal components, which will require a screwdriver to install. This kit comes with all the necessary parts for a dishwasher rack adjuster. It fits onto the dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. In many cases, our customers have reported the top rack of their dishwasher hanging down or sagging due to the adjuster kit, particularly if the wheels, have broken or failed. If you are having problems in this area, this kit will help get your dishwasher back up and running. Check your model number and user manual to see if this part is right for you. The parts for this kit come as a package and are not generally sold individually.

This genuine OEM water supply manifold or tube is specially designed for various models of dishwashers. It fits onto the upper rack of the dishwasher. The manifold distributes water from the main water supply line, through the spray arm, to various parts of the dishwasher where it is needed for cleaning dishes. When the dishwasher is turned on, the water inlet valve opens, allowing water to flow into the manifold. If the manifold is damaged, or no longer functioning properly it will be unable to distribute water to the spray arms leading to uneven cleaning, water leakage, difficulties completing cycles and reduced energy efficiency.

Also know as a diverter valve. This diverter motor is for dishwashers. Diverter motor controls the flow of water to the spray arms. Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.

The upper spray arm rotates and sprays water to clean the dishes inside the dishwasher tub. If your dishes are not being cleaned properly, you should check if there is an issue with the spray arm. To check your spray arm, make sure the spray arms can move evenly and freely on their bearing rings and mounting brackets. Remove your spray arm and check to ensure they are straight and undamaged. This spray arm is made of high-quality plastic and is just over 5 inches long.

Sold individually.

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.

Sold individually.

This genuine OEM thermostat is sourced directly from the manufacturer to ensure compatibility with your dishwasher model. The thermostat monitors and regulates the temperature of the dishwasher heating element. It is responsible for ensuring that the water temperature reaches the optimal level for effective cleaning while also helping to prevent overheating and potential damage to the internal components of the dishwasher.

Detergent dispenser W10861000 is an original equipment manufacturer (OEM) part that fits some Whirlpool, KitchenAid, Maytag and Amana dishwashers. Detergent dispenser W10861000 attaches to the inner door panel and holds the dishwasher detergent and rinse aid in covered compartments. This dishwasher detergent dispenser measures approximately 5 inches wide and 4.5 inches high.

This pump and motor assembly are for dishwashers. Pump and motor assembly pumps water through the spray arms during the dishwashing cycle. Shut off the house circuit breaker for the dishwasher before installing this part. Wear work gloves to protect your hands.

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the dishrack. If your clip is cracked or damaged, it is best to replace this part. To repair, first lift the release tab and hold the other side to prevent it from falling off. After lifting it off, you can set the new clip on the tine row and lock it up. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to wear work gloves as a safety precaution. This repair was rated as very easy by our customers and should be done in 15 minutes or less.

This drain hose is 6 and 1/2 feet.

This is a door latch for various dishwashers. Door latches are designed to communicate with the control board of the dishwasher when the door is closed and latched shut. If your dishwasher is not latching shut properly, or if your dishwasher will not start when the door is shut, then this latch is likely broken or bad. To replace this door latch, you will need a screwdriver or drill, and a set of pliers. This latch is sold individually, and does not come with any securing screws or other parts.

Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip holds the adjuster arm in the right position on the dishrack. The most common reason for replacing the strap is if the rack will not stay in its desired position. This part is sold individually. There are no tools needed to replace the positioner.

Introduce supreme functionality to your dishwashing process with the Whirlpool Feed Tube Assembly. As an authentic OEM part, it is designed to complement select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers. This assembly plays a crucial role by feeding water from the pump to the center wash arm and the top spinner. It ensures optimal water distribution, promising an efficient clean. The assembly has a precise fit, although it's advised to verify the part number before ordering, as variations can occur in size and shape. Using this assembly during repairs may require gloves for your safety. With its robust and reliable design, this Whirlpool Feed Tube Assembly can help keep your dishwasher performing at its highest potential.

This pump inlet grommet is a genuine OEM replacement part that is compatible with various models of dishwashers. It is made of rubber and has a diameter of approximately 2.5 inches. The grommet is used to create a watertight seal in the area between the inlet hose and the circulation pump. This prevents the dishwasher from leaking, and it also helps to absorb minor shocks and vibrations that occur while the dishwasher is running. It is normal for the grommet to wear down over time or become damaged from exposure to water, heat, and chemicals.

This part is used to drain water from your dishwasher.

Introducing the genuine OEM Support Bracket from Whirlpool, designed exclusively for securing the water supply tube in your dishwasher. Crafted to offer exceptional performance, this accessory is compatible with specific models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. To confirm its compatibility, cross-check this bracket with the model of your appliance before ordering. Remember to safely unplug your dishwasher and shut off the water supply before installation. For best results and to avoid potential injury, always wear work gloves during installation. Restore the efficiency of your dishwasher with this superior Whirlpool Support Bracket.