Parts That Fix Whirlpool Dishwasher WDF520PADM7 Not cleaning dishes properly

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.

This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.

The spray arm manifold holds the spray arm and connects the spray arm to the water feed tube.

This pump and motor assembly is for dishwashers. Pump and motor assembly pumps water through the spray arms during the dishwashing cycle. Shut off the house circuit breaker for the dishwasher before installing this part. Wear work gloves to protect your hands.

This drain hose is 6 and 1/2 feet.

This genuine Whirlpool cover is a key component of your dishwasher, compatible with several models under the Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef lineups. It serves as a sump cover, attached to the tub bottom, channeling and collecting water directly into the pump to ensure optimal functioning. For your safety, we recommend unplugging the dishwasher or switching off the house circuit breaker before installing this piece. A pair of work gloves is also advised to guard your hands during installation. Be certain of the part number's compatibility with your particular model before purchasing. Its design may vary in size and shape so a precise fit is essential for appropriate functioning.

This is a door latch for various dishwashers. Door latches are designed to communicate with the control board of the dishwasher when the door is closed and latched shut. If your dishwasher is not latching shut properly, or if your dishwasher will not start when the door is shut, then this latch is likely broken or bad. To replace this door latch, you will need a screwdriver or drill, and a set of pliers. This latch is sold individually, and does not come with any securing screws or other parts.

This is a replacement cap for the detergent/rinse aid dispenser. If the rinse aid cap is damaged or missing, you may notice too much rinse aid in the dishwasher. The cap simply screws in to the dispenser, so if your cap is damaged you can simply screw it out, then screw in the new one. The rinse aid cap is approximately 2 inches in diameter and is sold individually. This is an OEM part, directly from the manufacturer.

This pump inlet grommet is a genuine OEM replacement part that is compatible with various models of dishwashers. It is made of rubber and has a diameter of approximately 2.5 inches. The grommet is used to create a watertight seal in the area between the inlet hose and the circulation pump. This prevents the dishwasher from leaking, and it also helps to absorb minor shocks and vibrations that occur while the dishwasher is running. It is normal for the grommet to wear down over time or become damaged from exposure to water, heat, and chemicals.

This part is used to drain water from your dishwasher.

This detergent dispenser is an authentic replacement part sourced directly from the manufacturer to ensure compatibility with your dishwasher. The dispenser holds and releases detergent during the wash cycle. It has a lid that opens at the appropriate time in the wash cycle to release the detergent into the dishwasher. If the dispenser is faulty, it may be unable to open during the wash cycle, resulting in dishes not being properly cleaned or detergent residue remaining in the dispenser after the cycle has been completed. You may also notice leakage of detergent around the dispenser area. It is important to replace the dispenser promptly to avoid inefficient cleaning and detergent wastage

This silverware basket has two blue flip tops and a carrying handle. It is used in dishwasher as a place holder for cutlery and related items