Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches...
$5.95
In Stock
Order now and your part arrives in 2-3 business days!
This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Ma...
$7.63
In Stock
Order now and your part arrives in 2-3 business days!
The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy.
The part attaches inside of the fuel tank and is used to cle...
This spark plug is sourced from the original equipment manufacturer. It is a small device in the engine cylinder head which is responsible for creating the spark that ignites the fuel in the engine an...
Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of t...
$5.19
In Stock
Order now and your part arrives in 2-3 business days!
The m10 Left Hand Thread Nut is a 10mm, gold metal part, sold individually. This nut is a "reverse thread". It requires a wrench or socket set to install, and installation is rated as "Easy". Use this...
$5.19
In Stock
Order now and your part arrives in 2-3 business days!
The Cotter Pin (or Split Pin) is a 2x22mm silver metal part, sold individually. It is rated as "Easy" to install, and installation will require a set of pliers. It can be attached in various locations...
$4.99
In Stock
Order now and your part arrives in 2-3 business days!
Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of meta...
$5.95
In Stock
Order now and your part arrives in 2-3 business days!
This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to se...
$5.95
In Stock
Order now and your part arrives in 2-3 business days!
Questions And Answers for SRM-2601
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Thru fuel cap, insert copper wire with hook formed on end. Fish around until you grab the fuel line. Pull the fuel line and filter thru the fuel fill neck. Pull off old filter and replace with new. Push back into fuel tank & be done.
Easiest repair ever. Turn the trimmer upside down so you can access the string assembly. Find the small hole in the shaft beneath the string assembly and insert a heavy gauge nail into it to hold the shat in place. Turn the string assembly counterclockwise until it comes off. Lift off the round metal piece that was under the string assemb
... Read morely.Find the 3 screws holding the shield in place and unscrew them. Pull the shield off. Install the new one in reverse order. I used the original hex screws as the new ones were philips head. Hex worked perfectly. I was amazed how easy thus was to do.
