R13C Husqvarna - Overview
Models starting with R13C
Click on the best match to narrow your results.
- R13C ( 965094301 2008-04 ) Husqvarna Lawn Tractor (Swedish Riding Mower)
- R13C ( 965070401 2006-01 ) Husqvarna Lawn Tractor (Swedish Riding Mower)
- R13C ( 965094301 2009-04 ) Husqvarna Lawn Tractor (Swedish Riding Mower)
- R13C ( 965094301 2007-01 ) Husqvarna Lawn Tractor (Swedish Riding Mower)
- R13C ( 965094301 2010-07 ) Husqvarna Lawn Tractor (Swedish Riding Mower)
- R13C5 ( 966600401 2012 ) Husqvarna Lawn Mower (Rider)
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Flange Wheel Bearing
PartSelect #: PS9006914
Manufacturer #: 532009040
The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft....
$9.18
In Stock
Lawn Mower Ring Clip
PartSelect #: PS9143890
Manufacturer #: 812000029
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle.
This part is black, made of metal, and around an inch in length. It i...
$5.95
In Stock
Lawn Mower Hex Head Bolt
PartSelect #: PS9982804
Manufacturer #: 584953901
This part is the replacement washer head screw for your lawn tractor. It is black in color and is approximately an inch and a half in length. This self-threading screw is most commonly used for securi...
$3.99
In Stock
Lawn Mower Washer
PartSelect #: PS9008998
Manufacturer #: 532121749
This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending...
$3.99
On Order
Lawn Mower Blade Bolt and Washer Assembly
PartSelect #: PS9020856
Manufacturer #: 532193003
This manufacturer-approved bolt and washer assembly is for lawn tractors.
Wear work gloves to protect your hands when installing this part.
$9.62
In Stock
Lawn Mower V-Groove Idler Pulley
PartSelect #: PS9016377
Manufacturer #: 532194326
This ground drive fixed idler pulley is for lawn tractors.
910 inch offset
Ground drive fixed idler pulley helps apply tension to the drive belt, allowing the belt to turn.
Wear work gloves to...
$21.22
In Stock
Lawn Mower Flat Idler Pulley
PartSelect #: PS9016399
Manufacturer #: 532194327
This flat idler pulley is a genuine OEM replacement part for use in outdoor power equipment. It is made of plastic and features a metal bore adapter, and a radial-style single row bearing. The pulley ...
$19.09
In Stock
Lawn Mower Ignition Switch
PartSelect #: PS9020864
Manufacturer #: 532193350
This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various fu...
$24.40
In Stock
Lawn Mower Hardened Washer
PartSelect #: PS9015920
Manufacturer #: 532188967
This OEM hardened washer spreads load under the bolts of your lawn tractor. It is silver, made of metal, and is sold individually. Over time, the washer may become damaged due to wear and fatigue, and...
$4.99
In Stock
Lawn Mower Pulley Idler
PartSelect #: PS9287043
Manufacturer #: 532196106
This replacement idler pulley is an original part sourced directly from the equipment manufacturer and is designed for use with select Poulan and Husqvarna riding lawn mowers and garden tractors. It p...
$40.32
In Stock
Extension Spring
PartSelect #: PS12608566
Manufacturer #: 587358401
This is an extension spring specifically designed for Husqvarna lawnmowers. The spring.extn.42.fcs.tr.deck.drv can be used as a replacement to regain the optimal running condition of your gardening eq...
$11.48
Special Order
Common Symptoms of models starting with R13C
[Viewing 2 of 2]Drive system does not work
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Husqvartna LGT-48DXL transmission drive belt was worn out
ALL VIDEOS and the official Husqvarna instructions will tell you that you MUST remove both the mowing deck and the entire clutch pulley assembly to switch the transmission drive belt. This is NOT true. It takes some effort and tight maneuvering, but this job can be done relatively quickly without removing either. You do NOT have to rem
... Read more
ove the mowing deck! You do NOT have to remove the clutch pulley assembly! What I did was to stand the tractor up nearly vertical, resting it against a golf cart I have and tying it in place for safety. Then, you have to loosen two black belt guides right by the clutch pulley assembly. I did NOT remove them, just left them hanging loose. Next, there is a silver bar that comes in from the outside of the mower chassis and attaches directly to the clutch, remove this entirely. Next, there is an electrical cord assembly in the way, trace this back, find where it plugs in, and unplug it. Next, in order to be able to slide the belt fully over the clutch pulley assembly, you have to take the mower deck belt off of JUST THE ONE spindle closest. I tie wrapped it in place after getting it off the spindle so that I could easily put it back onto the spindle as the last step when done. Once the mowing deck belt is off the closest spindle, you can then slide the drive belt completely over the clutch pulley assembly. You can then easily remove the entire drive belt, taking note (I took pictures) of how it is routed. Then, just reverse all of this. I began by fitting the drive belt over the clutch pulley assembly to make sure that end was correct. I then put the previously mentioned two guides, silver bar, and electrical cord back in place. Next, I shoved the belt down where it goes, working it down towards the transmission and routing it correctly. Of course, it is a little difficult with the limited space available, but I would rather do that then needlessly take the entire mowing deck off. You finally have to CAREFULLY slide it over the PLASTIC fan blades on the transmission. Once past those, it slides easily in place. The last step is to put the mowing deck belt that you previously removed and tie wrapped in place back onto the spindle. That's it! Only takes about 30-45 min. done this way.
Read less
Parts Used:
-
Daniel from WYTHEVILLE, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable)
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original shield was damaged
-
Wayne from LAKEVILLE, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken weld on right axle
Removed wheel (used strong magnet to catch the keeper)
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Parts Used:
-
walter from EDINBURG, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!