PRD364GDHU (01) Thermador Range - Overview
Sections of the PRD364GDHU
[Viewing 10 of 10]
Keep searches simple, eg. "belt" or "pump".
SWITCH
PartSelect #: PS8714254
Manufacturer #: 00428049
This OEM control panel switch, also known as a limit switch or limit sensor, is mounted within the control panel housing on ranges. It is a small component that is responsible for transferring power t...
No Longer Available
Questions And Answers for PRD364GDHU
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Richard
January 9, 2020
I have a 4 burner with a griddle in the center. The gas burners on the left side stopped working, no spark from the ignition plug or gas. The blue display light comes on when knob is turned. The right burners, griddle and oven work fine. I removed the tray but don't see anything that looks like it could be burnt out like wires, valve control, simmer control kit, etc.
For model number PRD364GDHU
Hello Richard, thank you for your question. That sounds like an issue with the spark module. We would recommend replacing PartSelect Number PS8728436 first. I hope this helps.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Four extra Low burner igniters malfunctioned, Sparking when burner off.
The sole review for this part by Andrew was most helpful and accurate with one exception: he said that there were two nuts Which needed to be removed in order to pull off the front knob panel. There were actually two on each end for a total of four, which confused me, as I wondered if I had the right ones. Another thing that would be help
... Read more
ful for somebody considering doing this repair is to know that it takes a deep quarter inch socket With two 6 inch extensions to reach these nuts through holes in the interior side panels. Also, take a look at the replacement potentiometers, and you’ll see that there’s a slot that can be lined up so that they can be pulled off the side of the shaft rather than off the front of the shaft. This repair took me about six hours. I’m mechanically inclined and work methodically, but since I’ve never done this repair before it was quite time-consuming.
Read less
Parts Used:
-
Robert from GREENWOOD VLG, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Socket set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven does not maintain consistent temperature
Remove slide racks from oven. At the back right corner of oven unscrew heat sensor probe. Access rear of range. Remove screws holding back panel. Find wire from temperature probe where it passes through back wall of over and unclip it pulling probe wire and probe out back of oven. From the inside of oven, push chopstick through hole probe
... Read more
wire was routed through, to find hole in back wall of oven. Once chopstick is visible from back of oven, with chopstick enlarge hole through visible insulation. This is the opening the new probe wire needs to be routed through. From inside oven push new wire, using chopstick, through this hole and reattach wire at back of oven using the plastic clip on the wire. From inside oven screw probe to back of oven wall, reattach outside panel to back of oven, turn gas back on, plug range back in, check oven operates, and push range back in place, reinstall racks. You may have to remove oven door if you have trouble reaching to the back of the oven to access the probe. YouTube videos are easy to find showing how to do that.
Read less
Parts Used:
-
David from LONG BEACH, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!