PDR364GLZS Bosch Range - Overview
Sections of the PDR364GLZS
[Viewing 11 of 11]
Keep searches simple, eg. "belt" or "pump".
IGNITION HEAD
PartSelect #: PS8698440
Manufacturer #: 00189324
This is a cooktop burner igniter that is compatible with various makes and models of cooktops and ranges and is sold as an individual part. This part creates a spark that ignites the burner within you...
$63.60
In Stock
SPACER
PartSelect #: PS8709371
Manufacturer #: 00413552
This spacer kit, also known as a grate foot kit, is a set of four padded feet designed to protect your burner grates and prevent scratches on the cooktop. Typically located at the bottom corners of th...
$30.92
In Stock
TUBE
PartSelect #: PS8698345
Manufacturer #: 00189023
This authentic OEM venturi tube, also known as a gas tube connector or surface burner tube, mixes gas and air to create the proper fuel-air mixture for combustion in your range. It is typically locate...
$62.04
In Stock
NUT
PartSelect #: PS8698313
Manufacturer #: 00188978
This nut is designed for use with different makes and models of ranges and cooktops and is a genuine OEM part. This nut is 1mm thick and is 22-threads-per-inch, and is made of high-quality, durable st...
$23.41
In Stock
SWITCH
PartSelect #: PS8714254
Manufacturer #: 00428049
This OEM control panel switch, also known as a limit switch or limit sensor, is mounted within the control panel housing on ranges. It is a small component that is responsible for transferring power t...
No Longer Available
Questions And Answers for PDR364GLZS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part discontinued by Bosch. Found replacement part at Parts Select
Removed knobs and venturies. Unplugged electrical inputs. Lifted top plate. Replaced potentiometer. Replaced parts and plugged in electric supplies. Tested. Piece of cake, except for locating replacement potentiometer.
Parts Used:
-
Charlie from INDIAN SPGS, AL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench (Adjustable)
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven does not maintain consistent temperature
Remove slide racks from oven. At the back right corner of oven unscrew heat sensor probe. Access rear of range. Remove screws holding back panel. Find wire from temperature probe where it passes through back wall of over and unclip it pulling probe wire and probe out back of oven. From the inside of oven, push chopstick through hole probe
... Read more
wire was routed through, to find hole in back wall of oven. Once chopstick is visible from back of oven, with chopstick enlarge hole through visible insulation. This is the opening the new probe wire needs to be routed through. From inside oven push new wire, using chopstick, through this hole and reattach wire at back of oven using the plastic clip on the wire. From inside oven screw probe to back of oven wall, reattach outside panel to back of oven, turn gas back on, plug range back in, check oven operates, and push range back in place, reinstall racks. You may have to remove oven door if you have trouble reaching to the back of the oven to access the probe. YouTube videos are easy to find showing how to do that.
Read less
Parts Used:
-
David from LONG BEACH, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!