P4018 Chainsaw - Overview
Models starting with P4018
Click on the best match to narrow your results.
- P4018 Poulan Chainsaw (Gas Chainsaw)
- P4018 ( Type1 2008-07 ) Husqvarna Chainsaw (Wt Chain Saw)
- P4018 ( Type2 2008-07 ) Husqvarna Chainsaw (Wt Chain Saw)
- P4018 ( 952802151 2012-01 ) Poulan Chainsaw (Chainsaw)
- P4018AV ( Type1 2008-07 ) Husqvarna Chainsaw (Chain Saw)
- P4018AV ( Type2 2008-07 ) Husqvarna Chainsaw (Chain Saw)
- P4018AV (Type 2) Poulan Chainsaw (Gas Chainsaw)
- P4018AV (Type 1) Poulan Chainsaw (Gas Chainsaw)
- P4018AV-BH (Type 2) Poulan Chainsaw (Gas Chainsaw)
- P4018AV-BH (Type 1) Poulan Chainsaw (Gas Chainsaw)
- P4018AVBH ( Type1 2008-07 ) Husqvarna Chainsaw (Chain Saw)
- P4018AVBH ( Type2 2008-07 ) Husqvarna Chainsaw (Chain Saw)
- P4018WM ( Type1 2008-07 ) Husqvarna Chainsaw (Chain Saw)
- P4018WM ( Type2 2008-07 ) Husqvarna Chainsaw (Chain Saw)
- P4018WM (Type 2) Poulan Chainsaw (Gas Chainsaw)
- P4018WM (Type 1) Poulan Chainsaw (Gas Chainsaw)
- P4018WT (Type 2) Poulan Chainsaw (Gas Chainsaw)
- P4018WT (Type 1) Poulan Chainsaw (Gas Chainsaw)
- P4018WT (TYPE 3) Poulan Chainsaw (Chainsaw)
- P4018WTL Poulan Chainsaw (Gas Chainsaw)
Keep searches simple, eg. "belt" or "pump".
Trimmer Fuel Filter
PartSelect #: PS9285148
Manufacturer #: 530095646
This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this esse...
$5.95
In Stock
Chainsaw Fuel Line
PartSelect #: PS9472280
Manufacturer #: 530069247
This is the replacement fuel line 25 Inch for several OPE products that use small engines. The fuel line carries fuel from the tank to the carburetor. Over time, the fuel line can become badly clogged...
$9.93
Special Order
Chainsaw Purge Line
PartSelect #: PS9472264
Manufacturer #: 530069216
This part is the replacement tank/purge line for your outdoor power equipment. It is made of clear plastic and is sold individually. The tank/purge line returns excess fuel from the carburetor to the ...
$8.98
Special Order
Chainsaw Purge Bulb
PartSelect #: PS9471212
Manufacturer #: 530047721
This primer bulb, also known as a purge bulb, is used to push more fuel from the fuel tank into the carburetor of your small engine equipment, to help the engine start easier. Over time and through ex...
$9.93
Special Order
Chainsaw Fuel Line Fitting
PartSelect #: PS9469715
Manufacturer #: 530023877
The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "E...
$8.04
Special Order
Spark Plug
PartSelect #: PS9484192
Manufacturer #: 952030150
This genuine Spark Plug, RCJ8Y, is sold individually, comprised of steel and ceramic, and is white and silver in color. The function of the spark plug is to ignite a mixture of air and fuel in the com...
$5.71
Special Order
Chainsaw Fuel Cap Assembly
PartSelect #: PS9982262
Manufacturer #: 580940901
This part is the replacement fuel cap assembly for your chainsaw. It is made of black plastic and is sold individually. The fuel cap prevents fuel from spilling out of the chainsaw and prevents debris...
$8.72
Special Order
Chainsaw Recoil Starter Spring
PartSelect #: PS9482322
Manufacturer #: 545008013
Also referred to as a Recoil Spring, this OEM replacement part is used to rewind the pull rope back into the starter housing. This Spring is sold individually, not as part of a kit or assembly, and is...
No Longer Available
Carburetor
PartSelect #: PS9482465
Manufacturer #: 545070601
This is an authentic replacement carburetor which is supplied by the original equipment manufacturer for use with Craftsman chainsaws. The purpose of this part is to mix the air and the gas before the...
$64.34
Special Order
Chainsaw Bar Adjustment Kit
PartSelect #: PS9472355
Manufacturer #: 530069611
This Chain Bar Adjuster kit is a kit which contains all necessary hardware for adjusting a chain bar on a chain saw. Installation is rated as "Easy" and requires a screwdriver, wrench set and socket s...
$12.59
Special Order
Chainsaw Mounting Bar Nut
PartSelect #: PS9469166
Manufacturer #: 530015917
The OEM Mounting Bar Nut is a nut used to install a mounting bar to your machine. Installation requires a wrench set and socket set, and is rated as "Easy". This nut attaches to the chainbar studs.
$5.95
Special Order
Common Symptoms of models starting with P4018
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Engine stops after a few seconds or minutes
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both the Fuel line and the Engine fuel line, where dry rotted.
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa ... Read more ll into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa ... Read more ll into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
Read less
Parts Used:
-
Victor from SCOTTSVILLE, KY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
47 of 62 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the fuel lines
Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose.
Instead of running the line into ... Read more the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through.
Instead of running the line into ... Read more the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through.
Read less
Parts Used:
-
Robert from MANVILLE, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
19 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not start , had been sitting for years,
I did not write detail steps , basically remove old carb replaced with new one, reassembled started right up no adjustments were needed !
Parts Used:
-
Sherri from BREAUX BRIDGE, LA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!