NE59J7651WS (AC-0000) Samsung Microwave Oven Combo - Instructions

I removed the control panel with a Phillips screwdriver and unplugged the burner switch and replaced the new switch and put the control panel back in place and turned on the burner and it worked as it should.i realized that I only would have only had to remove the 4 screws on the bottom of the control panel. All I would have had to do was just take those 4 screws out and remove the switch control knob and the two screws that held the switch in. Am very happy with the results

My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!

I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11.

ordered the temp sensor for a standard complaint, new sensor was the correct part ordered, however, once the old sensor was removed, I ohm'd the original and the new part. Both were 1080, checked wiring, checked gas burner, checked line voltage. Searched other part prices, found Samsung to be a not desirable product to own. This non repair was to help my neighbor who lives on a fixed income. Checked oven temp with the oven at 350 f setting, oven was 223 f. Set oven to 465 f and fount the oven at 353 f. I wanted to return the part but she insisted I install it anyway and found the oven doing the same thing. She did not want to throw more money at a 4 year old range. Will use it as it is but will buy a cheap oven temp gauge. Samsung sucks.

Cool oven, open door. Turn off electrical power. I laid a cloth over door to protect and to catch ant screws that my fat fingers would drop. I removed 4 screws under control panel. I pulled panel up and off stove face. My wife held it safely as I removed the triple burner knob. I then placed new switch, on stove top in same position as old one. I then removed screws holding old knob to release from control panel. The removed electrical connections one at a time and installed on new switch. Reinstalled switch back in control panel. Reinstalled control panel. Placed knob back in place. Turned electrical power back on. Then tested burner. Wife is happy and so am I.

First turn off the breaker for your oven/range, then open the oven door and look up at the control panel where the controls are. There are four screws holding it in place. Remove them and wiggle the control panel away from the stove top. Before you remove the four wiring connectors from the old switch box take a picture so you will know how they go back on. Remove the wiring connectors and pull the control knob off its shaft. There are two screws behind the control knob that secure the switch box to the control panel. Remove them. Install the new switch box before attaching its wiring connectors which will make it easier to line up the screw holes behind the control panel.

Remove back sheet metal covers. Disconnect temp. Sensor. Open oven door and remove grates. Remove two screws holding sensor to back oven wall. Pull out and then replace with new one. Assemble connections in back and replace sheet metal covers.

Just a few screws hold on the faceplate beneath the switches - then the actuator just plugs in! Then replace the screws
For $185 and 10 mins I saved a $1500 range/oven.
Yay Partselect for having the part available:)

Followed the tutorial, making things easy.

Turned off circuit breaker, unplugged from wall. Removed dials from front of range. Removed back top panel, and removed Phillips screws holding the associated switches to the front panel. Installed new switches and moved the wiring connectors from old to new switches. Replaced the back panel and front dials. Restored power and tested. So simple even an old phone guy could do it…

My repair went terrible as I was sent the wrong motor 2 times. My stove sat in the middle of my small kitchen for 2 weeks. Finally the 3rd was the correct one except I didn't have the right nut so I waited another day for that to be sent. Everything working good now, I just hope the bottom fan doesn't go out after this experience.

Pulled off the back panel (6 screws) thermostat was right there removed 2 wires and replaced with new put the panel back on done