Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
This is a seal, but you may also know it as a door gasket and it is for your dishwasher. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping duri...
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$51.43
In Stock
Questions And Answers for MDB4949SHZ1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Andy
April 19, 2023
Hello, my dishwasher works fine when it does run. However every few times I use it will only start and run for about 2-3 minutes, drain and shut off with no lights on. It will normally work when I restart it, though sometimes it will do it twice in a row. Any ideas?
For model number MDB4949SHZ1
Hi Andy, thank you for reaching out. The issue is probably due to the control board, part number PS12583931. We hope this helps!
My dishwasher appears to be functioning and cleaning normally but there is a smell that remains on the dishes. We have tried baking soda and vinegar, empty cycle with afresh or a regular dish pod, and thoroughly cleaning the lower filter as well as visually inspecting the sprayer arms and assembly. Nothing was particularly dirty so I wonder if the chopper blade and mesh in the motor is clogged/dirty. Because it is inaccessible without uninstalling the dishwasher, are there other areas we should clean first? Any tips or ideas is greatly appreciated!
For model number MDB4949SHZ1
Hi Victoria, thank you for contacting us. We have researched the model and would suggest making sure the circulation pump motor, part number PS11723102, is clean. A dirty motor may cause the dishes to smell bad. We would also suggest checking the gasket seal, part number PS16875904, and making sure it is not moldy. With all of the moisture and heat that your dishwasher produces, the gasket can become a breeding ground for mold and mildew. Removing the door seal and cleaning it from the inside may help. Glad to be of assistance!
I need the dishwasher door and the computer part's and control's inside the door... please and thank you
For model number MDB4949SHZ1
Hi Nathan, thank you for getting in touch. We have found that the door for your model comes as two separate parts and not an assembly. The inner door is part number PS11765868, and the outer door panel is part number PS12584465. Also, the control board listed for your model is part number PS12583931, and the control panel is part number PS12731162. Please submit a new question if you have any follow-ups!
I have a broken clip that holds the upper rack to the sliding bar. It is a round gray piece of plastic that fits into a round white piece of plastic. I can put them back together, but it comes right out again.
For model number MDB4949SHZ1
Hi Charles, thank you for reaching out. The issue seems to be with the dish rack adjuster and wheel assembly, part number PS11756470. It comes as an assembly. You may need to replace it to fix the issue. We hope that helps!
Thanks for letting me know about part No. PS11756470, for the upper dish rack. It looks like the right part. However, I also need the number for the corresponding male part, as I am not sure which part is broken.
For model number MDB4949SHZ1
Hello Charles, thank you for reaching out. The part you are looking for is the dishrack track, part number PS11741377. This track attaches to the inside of the tub for the upper rack to glide in and out. We hope this helps.
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i
... Read morenput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
