LISR310CW1WW General Electric Washer - Overview
Sections of the LISR310CW1WW
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Washer Dampening Strap
PartSelect #: PS271100
Manufacturer #: WH1X2727
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash c...
$34.95
On Order
Washer Timer Knob
PartSelect #: PS1482286
Manufacturer #: WH01X10310
This is a replacement timer knob for your washing machine. To complete this repair you will need a pair of needle nose pliers. Turn off power to the washer before you start. Pull off the timer knob an...
$12.95
In Stock
Washer Agitator Coupling Kit
PartSelect #: PS1517844
Manufacturer #: WH49X10042
The agitator coupler connects the agitator to the agitator shaft. Common symptoms of a damaged coupler include: a grinding sound during the wash cycle, the washer refusing to agitate or spin, or the w...
$41.95
In Stock
Knob and Clip
PartSelect #: PS268450
Manufacturer #: WH01X10060
This knob accepts a D-shaped shaft.
$28.95
In Stock
Tub Bearing Washer
PartSelect #: PS271509
Manufacturer #: WH2X1197
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a w...
$13.95
In Stock
Washer Split Ring
PartSelect #: PS1766022
Manufacturer #: WH02X10265
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. T...
No Longer Available
Washer Knob Dial
PartSelect #: PS756514
Manufacturer #: WH11X10033
This part is a replacement knob dial for your washer. The knob dial rotates and allows you to select your desired settings. It is a round piece of white plastic with a small, triangular gray arrow on ...
$44.95
In Stock
Socket Rod Support - White
PartSelect #: PS268394
Manufacturer #: WH01X10001
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the ro...
$13.95
In Stock
Washer Tub Base Hub
PartSelect #: PS273296
Manufacturer #: WH45X10027
This part is the replacement inner tub base hub for your washer. It is made of metal and is approximately 15 inches in diameter. The inner tub base hub fits between the wash tub and the spin basket, a...
$79.33
In Stock
Washer Screw
PartSelect #: PS268950
Manufacturer #: WH02X10002
This screw is sold individually.
$13.95
In Stock
Washer Water Fill Nozzle
PartSelect #: PS756806
Manufacturer #: WH41X10077
This part is the replacement water fill nozzle for your washer. It is white and tan in color, made of plastic, and is approximately 7 inches long and 4 inches wide. The water fill nozzle is also known...
$22.95
In Stock
Transmission and Brake Assembly
PartSelect #: PS271743
Manufacturer #: WH38X10002
This transmission and brake assembly comes with a new tub seal. This kit aids in the spinning or agitating cycles.
No Longer Available
Questions And Answers for LISR310CW1WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the LISR310CW1WW
[Viewing 10 of 10]Will not agitate
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Cycle Not Advancing
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Control knob teeth were worn
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
Parts Used:
-
Charles from Dallas, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
508 of 514 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken dampening strap and loose agitator
first remove the front washer cover by finding the two pressure clips that hold it to the top lid. gently push the putty knife into the clips one at a time. this will raise and separate them from the front panel. the panel will tilt forward and u can now remove it from the bottom clips by sliding it up and out. to open the top cover u rem
... Read more
ove the two 1/4 in screws on the sides of the front panel and lift the top. make sure to secure it in place or unplug the single electrical connection at the rear and remove the whole top from the clips, its really simple and the most convenient mehtod. to remove the straps u can now get to all four without much interference. there are two size screw heads so make sure u have a nut driver or small socket set. after changing the straps i went to change the agitator coupling. the agitator pulled directly up without a problem. just put your two hands under and pull straight up with one good jolt. the plastic coupler has one bolt in the middle that came out easily with a small socket set. my problem arose when the plastic coupler would not come off the metal shaft. after a short time of pulling and prying i finally decided to cut it off. using a small hacksaw and taking my time i put two cuts into the coupler. they were on opposite sides and where vertical, running along the steel shaft. i could now split it in two and it came off very easily and quickly. now when putting on the new one make sure the splines line up. push as far down as u can then use the center bolt to seat the gear all the way down. the agitator also has to be lined up just right. it also has splines on the interior that allow it to line up with the coupler and merely push down until it reseats itself in place. replace the top of the washer and then the front panel. don't forget to rebolt the top panel to the frame. push the front panel in until it snaps into place. full replacement time was about 40 minutes and actually not bad with the right tools.
Read less
Parts Used:
-
molly from laguna niguel, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
286 of 305 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator would not move during wash cycle
I placed both hands under the agitator 180 degrees apart, gave a quick jerk, and seperated the agitator from the coupling. With the agitator removed, use a socket and ratchet to remove the bolt holding the coupling to the spline. Remove the old coupling and slide the new one over the spline. Lightly tap on the coupling if necessary. I
... Read more
nsert the bolt with the ratchet and slide the agitator back over the coupling and you are done.
Read less
Parts Used:
-
Mark from Lexington, KY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
229 of 261 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!