LDS5774ST (ASTEEUS) LG Dishwasher - Instructions

Removed mounting screws from sides of disher. Removed broken piece of connector assy still attached to hinge. Attached new connector assy to hinge then looped it around pulley with spring attached to opposite end. Need both hands to pull spring up to side of tub and connect it. I would suggest replacing both connector assemblies while you have the dishwasher pulled out. Push dishwasher back in and mount with screws.

According to your site, the part(s), to consider, to resolve the problem were: 1.Motor Assembly DC Pump, OR 2.Drain Pump. I simply selected the drain pump because it was cheaper and because it was making a clicking noise. (The only significant noise that this dishwasher was making) To be safe, I unplugged the unit and turned off the water, under the sink. I removed the kick plate and I unscrewed the anchor clips from under the counter and carefully pulled the unit out. I then opened the dishwasher and removed the lower rack. To minimize water clean-up, I took a rag and soaked up the standing water in the bottom until it was nearly dry. I then tipped the dishwasher on it's left side, knowing where the location of the drain pump (front, right), would be in an easier location for me to work. I first unplugged the pumps wiring. Then, with pliers, I was able to disconnect the clips on the short, rubber hoses that hold the pump in alignment.(Use caution: If reusing the same rubber hose(s) on the new pump, it will be easier if you put them on in the same direction as they were take off) Then I removed the rubber supports off their hooks, that allow the pump to hang from the bottom of the dishwasher. Once the rubber hoses are re-connected on the new pump and placed on to it's former proper alignment, you can re-attach the rubber supports to their hooks. And last, but not least, remember to plug the new pump's wires back in place. Carefully stand up dishwasher and push it slowly back into place. I plugged in the unit and turned on the water. Before I screwed the unit back to the counter and kick plate back on the front, I ran a load and watched for leaks beneath the new pumps area. No leaks. "Easy, Peasy".

Replacing the spring and connector assembly (the cord had frayed and broken) was easy and took only a matter of minutes to do. Wrestling the dishwasher in and out of its space under the counter was very difficult. Because my kitchen is compact, I had to move the refrigerator first, then disconnect the Romex cable and water lines from the dishwasher before I could pull it fully from under the counter. The side panels have screws in the front and the back, so the appliance had to be moved out until its back was exposed. But I got the job done and the door works just like a new one now!

Shut off electrical breaker, Removed bottom cover plate by removing 2 Phillips head screws. I was able to remove the pump without pulling the dishwasher out by removing wiring connection, hose clamps with a pair of pliers, and removed the 2 rubber hangers However I couldn’t reinstall the pump without pulling the dishwasher out. 1.I disconnected the electrical wiring (breaker was shut off). 2. Shut the water supply off and removed water line at the dishwasher. 3. Disconnected the drain at the sink. 4. Removed the 2 retaining screws 1 on each side that secures the dishwasher in place. 4. Removed the upper and lower racks, Used a shop vac and sucked the water out of the bottom of the dishwasher. 5. Pulled the dishwasher out making sure the drain line came with it. 6. Laid The dishwasher over on the back side to the floor. 7. Reinstalled pump with new hose clamps and hoses that came with the pump. ( it probably would have been easier to remove the pump with the dishwasher pulled out) reinstall the wire connection to the pump (snap in connection), connected the 2 new rubber hangers to pump and connected to the dishwasher . 8. Slide the dishwasher back in place and reconnect water line be sure and use some Teflon tape, reconnect electrical wiring, reconnect drain line, secure dishwasher with screws. Turn water on and check for leaks, turn electrical power back on. I ran the dishwasher to make sure it worked and make sure there weren’t any leaks before I installed the bottom cover plate.
I had an appliance service person say that they wouldn’t work on an LG because they were hard to work on and very difficult to get parts. My experience was just the opposite thanks to partselect. The Dishwasher works like brand new.

We replaced the rusty with the new ones.

First do not watch the videos . They had you taking the insides all apart
when all you had to do is pull the unit out , twist the motor out and put the new one back in. Take nothing apart inside the dishwasher.

The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.

Ordered complete M030 Casing Assembly (RepairClinic Item # 4116143) after cleaning and testing rubber seal and pump assembly. Worked for two washes, then leak came back. To replace complete assembly, remove dishwasher from under sink, tip on back, disconnect all electrical and connectors to Case Assembly. Next, remove heater assemble (single nut) - this requires upward pulling to release the rubber washer and unit. Once removed unscrew the case assembly (four screws). That's it. Reverse the order to install.

Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.

Pull the dishwasher out from underneath the countertop took 2 minutes unscrewed the panel on the side one minute put the connector on one minute screwed the panel back on 1 minute put the dishwasher back underneath the counter two minutes very easy job

Snapped the rollers on.

I actually didn't remove whole drain pump assembly. Just removed the old pump motor by rotating. Lots of water drains out so be ready with an old towel. Then installed the new drain motor and tossed the new housing. No more water at the end of cycle!

Unscrew all screws on the inside of the dishwasher door. Carefully separate the front panel from the inside panel. Lift out the latch assembly, remove connectors from both sides using needle nose pliers. Reconnect to new assembly and situate back into place. Close front and inside panel, replace all screws, making sure the short and long screws go back to where they came from. Quick easy project to eliminate 2 trips from a repairman, 1 for the diagnosis and 1 to do the work!

My husband was able to slide the dishwasher out, and quickly replace the old connector assembly for the new ones. The old connector assembly had broken at the “rope”. Now the door opens slowly and is as good as new.

Took out old rack. Put in new rack. Done.

No other assembly required.