LDP6810SS LG Dishwasher - Instructions

This is apparently a widely known issue for LG, and since their call center was closed due to Coronavirus, I had no luck getting them to cover the repair. Not wanting to wait weeks of months for them to get off their duffs, I ordered the part and unscrewed the six screws holding the control panel on and unplugged the old part, plugged in the new part, and replaced the screws.

Works great now.

Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.

Snapped the rollers on.

Took off the broken one and snap on the new one.

Ordered the part after reading your web site about others having the same problem and that the new panel solved the problem. The panel is attached by six easy-to-remove screws. The only difficulty was with the electrical connector. The connector has a release tab you need to depress to disconnect, and the tab is not easily visible as it is on the on the back side as you hold the connector. Once I found the tab, the connector disconnected easily and also connected easily with the new part.

Turn off power to the system - turn breaker off or unplug. Open the door. Remove the six screws at the top. Disconnect the control panel. Connect the new panel. Restore power. Test that buttons work. Replace the screws. Very easy DIY that will save you on calling for repairs. Part came fast, easy to install. 5-10 min tops.

This was my first time repairing a dishwasher. I watched YouTube on how to remove the dishwasher from the cabinet. Afterwards, I removed the bottom of the dishwasher while it was laying flat to get to the motor and micro switch. The only difficulty I had was getting to the motor which required taking the bottom section off of the dishwasher. I could not get an appliance repair company to work on an LG dishwasher. My only option was to repair the dishwasher or bought a new dishwasher. Therefore, my wife and I decided to , make an attempt to repair this one with a backup plan of buying a new one. Luckily, we were able to fix this one within two hours.

This was a $999 dishwasher. We saved the cost of a new dishwasher by taking the time to fix this one.

Turn off power via breaker, remove 6 screws, unplug old control panel, plug in new panel, put screws back in. Very easy. All screws are accessible with the door open.

snapped on new axel-wheel assembly

Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.

The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.

I would just like to return these rollers and would like a return address.

Thank you!
Penelope

Snap off old broken holder . Snap new holders in. No issues.

I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.

Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.

These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.