LD-6100BB LG Dishwasher - Instructions

Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.

Unscrewed the screws, displaced the dispenser and re installed the screws

The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.

Relocated dishwasher to garage and set it up on a table (easier on back having it elevated). Connected temporary water supply, drained to a bucket.

Removed pump, and found it severely corroded, indicating leakage from pump shaft seal in sump. Inspection of seal revealed excessive wear, requiring sump replacement (there is no way to replace just the pump seal). I have photos of old pump & sump, but I don't see any way to upload them.

Removed sump from dishwasher with all components attached, swapped components over to new sump, reinstalled sump (with new sump gasket) and started dishwasher to check for leaks. The heater was the most difficult component to swap. Reinstalling the sump assembly was tricky.

Reinstalled dishwasher into kitchen cabinet.

Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.

Pull the dishwasher out from underneath the countertop took 2 minutes unscrewed the panel on the side one minute put the connector on one minute screwed the panel back on 1 minute put the dishwasher back underneath the counter two minutes very easy job

Turn off the power at breaker box. Disconnect the power at dishwasher since I needed to pull the unit all the way out of the cabinet to get to screws on the back side for this model. Find and remove the screws to the cover. Remove cover. In my case, the rope on the connector assembly had snapped. I replaced spring and connector identically to functioning side. Did need a pair of pliers to provide enough tension on spring to install. Reconnected cover and power and moved back into the cabinet. Easy repair and my wife wondered why I hadn't done it sooner.

The noise is caused by a defective motor bearing. The bearing fails due to water intrusion after the motor shaft seal in the sump assembly starts leaking. It maybe worthwhile to replace the entire sump assembly ( illustr. M007) instead of the motor only to prevent premature failure of the replacement motor.
(Unfortunately the shaft seal is not available as a separate part).

Snapped the rollers on.

Disconnect washer - pull out and turn on it's right side. Remove bottom plate (2 screws). Water intake valve is attached to water line. Disconnect water line. On the other end of the pump is a rubber hose. Disconnect hose by using a pair of pliers to open pipe clamp. Disconnect the electric line by pulling the pronged plug out of the pump. The part is composed of the pump and a metal mounting plate. They are connected by 4 screws. Remove the screws and pull out the back half of the pump. The front of the pump is attached to the washer frame by 2 screws. When removed you will notice an o-ring that forms the seal between the two halves. Remember this when installing the new pump. You will have to take the new pump apart because the whole part will not fit through the frame opening, thus the need to make sure the o-ring is properly seated. You can either install the mounting plate to the frame then attach the pump half or with half of the part in front of the frame and the other half behind the frame connect the two, then attach it to the frame. Reconnect incoming water line using teflon tape and a crescent wrench. Reconnect out-flow line with the pipe clamp and attach the power line. Since you have to take the new pump apart make sure the o-ring is properly seated as it will have a tendency to fall out. Reassemble the rest.

Took out old rack. Put in new rack. Done.

No other assembly required.

When I found the problem to be the check valve I reinstalled the drive motor and water pump, ordered the part I needed,Installed the new check valve, installed the rest of the parts and did a test run which corrected the problem.

My husband was able to slide the dishwasher out, and quickly replace the old connector assembly for the new ones. The old connector assembly had broken at the “rope”. Now the door opens slowly and is as good as new.

Took off the broken one and snap on the new one.

Loosened 3 screws and unhooked supply line and electric box and pulled it out.