JVM3160DF9WW General Electric Wall Oven - Instructions

I followed the generic trouble shooting directions on the web site. It suggested either diode, capacitor and/or magnetron. I test each. All tested OK except diode. It was supposed to measure open in one direction and appox 200k ohms in the other direction. My diode measured open in both directions (tried multiple times, multiple settings). I replaced the diode. The order process was great and it shipped immediately. I knew I was in trouble when I measured the new diode and it too was open in both directions. It was easy to install but unfortunately no joy - did not solve the problem. At this point it is likely cheaper just to buy a new one

Had to remove microwave from the wall. Then disassemble entire top assembly to get to the part. Easy enough to replace after that. Then just reassemble and reinstall. About 2hrs. total

Remove microwave and set on flat surface. Remove all screws on top. Remove all screws around back edge holding top on. Finally remove the screws on botton holding top on and remove top. On left side on top, remove 6 screws holding black channel in place. Also remove 3 screws holding metal top in place. Now lift black channel up and unplug 2 wires on cutout. Replace cutout and reinstall everything in reverse order. Worst part is taking microwave down and reinstalling.

just in 1 2 3 step easy way. First unplug the power cord,use a small flat-head screwdriver to pull out the plastic rivet pin,rotate the old cover counter clockwise to removed lift out the blade assembly, install the new cover stirrer fan by first positioning the blade assembly then align the cover and rotate it clockwise to secure, then replace the mounting plastic rivet pin;with the repair completed, plug the power cord back in and your microwave oven should be ready for use again. : )

The spacesaver is mounted over the stovetop. I removed the oven, then removed all the screws from the cover. Removed the cover and located the TCO and removed the wiring and the TCO. Ordered the part VIA internet and replaced it . It helps a little that I was Radar tec. and taught Electronics for 10 years and repaired lots of Microwaves. However anyone could do it just watch what you remove and replace in reverse order.

This is the second time replacing this fuse, last time was exactly one year ago. The first time I replaced it, I removed the oven from the wall & disassembled a number of things to reach the culprit. This time I left the oven mounted & was able to access the 2 grille mounting screws on the top of the grille & remove it. Next comes the black plastic air deflector held by two screws & is mounted in front & on the right, it is shown on the parts list just above part #1434. After removing it, remove the two silver cover screws in the front, this cover also doesn't have a part # but is shown to the right of part #1410. At this point you can lift this cover enough to access the fuse which is on the left & held in place by one tiny screw through the clamp at the top, (careful not to drop it when removing). PS: Don't forget to cut the power to the microwave before starting!

This was the second time I've had to open up the microwave. 1st time display would blank out but system would continue to operate. Found solder connections on board to LED display were defective. Resoldered and unit was fine. This time I found the connection to the oven cavity temp cut-off was bad, plastic connection cover melted. When unit operated bottom lead and wire would heat up. Couldn't measure a Discernable distance so either wire or connector connection surface was not sufficient to carry the current. 1st replaced sensor still wire heated up. Replaced connector and there was no sign how heat from resistances.

I attached the mounting plate to the wall as directed in the installation instructions which I had downloaded from GE. This procedure took 45 minutes to complete. I was then able to mount the microwave.

Followed the instructions on your website and a YouTube video. The diode was at a 90 degree angle which made it a little trickier. Unfortunately the repair did not resolve the problem. I ended up buying a new microwave for temporary use for less than ordering any more parts. We are pleased with your website, instructions, ease of installation though!

1. Removed the plastic rivet holding the stirrer fan cover in place.
2. Slipped a small pry bar under the cover to allow room to grip the cover and pull it out of its setting.
3. Removed the stirrer fan and placed in new cover.
4. Disposed of old rivet and cover.
5. Aligned new cover with rivet hole and pushed it up and into place.
6. The rivet comes in two (2) pieces: the actual rivet and a locking collar.
7. Pushed the rivet locking collar in place and pushed rivet into the collar.

It is easy to repair the burnt out bulb if one has the correct bulb. Your website is very user friendly and your service is great. I was not able to replace the bulb at this time because our RV is at the repair shop for some other matters. I am sure the installation of the new bulb will go smoothly. Thanks for asking. Sharry Kiehl

Unscrewed the vent at top of microwave exposing small access to bulb. The access to this was very limited so that was the major issue in changing the bulb. You needed small hands to do the job.

Required removing the old unit and disconnecting the exhaust ductwork and drilling new holes for attachment to the cabinet

Gently remove plastic rivet holding cover in place.Rotate cover slightly and pull down. Remove stirrer fan from old cover and place on new cover. Place cover back in microwave and rotate till rivet hole lines up and replace rivet. Done.

Remove pin and shift old cover plate clockwise to release cover. Remove and insert fan into new cover and replace cover by inserting cover plate tabs and turning counter clockwise. Insert new pin to connect new cover plate.