HDA3400G02WW Hotpoint Dishwasher - Instructions

Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.

The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.

I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.

First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...

It is a simple process to replace the drain solenoid on these dishwashers, having replaced several in the past few months.

After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 screws, and plugging in the wire harness.

I work on a 260 + unit property, as well as working for a property management company who rents single family homes.

PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.

The most difficult part was removing the dishwasher from below the counter. Once that was complete, I simply turned the washer onto it's front surface to access the pump easier. Simply disconnected the electrical connectors, loosened the three hose clamps holding the hoses to the pump. Lastly removed a stiff arm bracket holding the pump. Reversed the order to install the new one using a longer bracket provided with the new unit. Hooked up the electrical connections last and slid the washer back in place. The washer runs like new now and is not making noise. The replacement part was a perfect match.

Siimply removed the rack and replaced the wheel assembly. Very easy

In order to access the fill valve, dishwasher had to be removed from under countertop. Disconnected water supply line and drain hose under sink. Unplugged unit and removed 2 screws holding unit to countertop. I was then able to pull unit out and replace valve. After reinstallation, the same problem existed. Further research pointed to the control module, approx. $100.00 or the motor, approx. $250.00 - $300.00. I than began looking at new dishwashers, but I did email GE with the problem. They suggested I use citric acid or vinegar in hot water, pour into right rear portion of tub and wait 1/2 hour. After doing that, the dishwasher worked perfectly.

took dishwasher out- put on table to work on-removed wire brace- disconected drain outlet- disconnected top drive seal- removed wire clip connector- removed motor unit----------------
installed new motor/drain unit--used new longer wire brac used adapter to connect electical leads-
tightened clamps and bingo it worked and didnt' leak. good job on the supplying of all the necessary adapers.

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

Did the install a few days ago 4.25.11 and all went smoothly. The instructions that came with the kit were very straightforward and the diagrams were extremely helpful in locating brackets/hoses/connections. My dad thought he would just get down there and do it, but wasn't sure what to do. Using the directions with the kit, I had the motor and pump off in under 5 minutes. FOLLOW THE DIRECTIONS WITH THE KIT!

Some things to note:
- Get some towels/cups/bowls, we had some water leaking from the dishwasher and hoses.
- Be careful removing the dishwasher from the counters, go slow.


1. Shut off electricity
2. Shut off water. I just shut closed the line that went directly to the dishwasher.
3. Removed screws from bottom panel to expose motor and pump assembly.
4. Removed screws securing the dishwasher to the counters.
5. Slowly slid dishwasher from counter and rotated so door was facing the ground carefully to ensure wires/hoses were not pulled or crushed.
6. Removed screw from bottom of motor that was secured to the hanger.
7. Removed ground screw from bottom of motor.
8. Removed all wired connections from the motor and pump.
9. Loosened hose clamp securing the drain line and removed from motor.
10. Loosened 2x hose clamps securing the motor and pump assembly to dishwasher.
11. Ensured everything was clear and disconnected, and slowly removed motor and pump assembly from dishwasher.
12. Test fit new motor and pump assembly.
13. Reconnected 2x connections to the motor and pump.
14. Secured the ground wire to the motor and pump.
15. Slid motor and pump onto dishwasher and secured the 2x hose clamps.
16. Secured screw from the hanger cable to the motor and pump.
17. Reconnected water line to motor and pump, and tightened hose clamp.
18. Ensured all connections were made, hose clamps were tightened, and there were no extra connections.
19. Rotated dishwasher back onto feet.
20. Slowly slid dishwasher back into counters ensuring no cables or hoses were kinked or crushed.
21. Restored electricity and water to dishwasher, and then performed a quick test of one cycle to check for leeks.
22. Secured bottom panel and dishwasher to counters.
23. Enjoyed having a working dishwasher again!

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.