Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
GUD24ESSJ0WW General Electric Washer Dryer Combo - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
$37.95
In Stock
Order within the next 12 hrs and your part ships today!
This drum glide bearing is an authentic OEM replacement part that is compatible with dryers. It is white in color and made of highly durable plastic. The bearing allows the drum to rotate smoothly and...
$15.95
In Stock
Order within the next 12 hrs and your part ships today!
This OEM replacement dryer slide bearing is white in color, and approximately 3 inches long. The slide bearings are supportive linings for your dryer. If they have eroded, or are damaged, the drums wi...
$23.95
In Stock
Order within the next 12 hrs and your part ships today!
Restore reliable operation to your GE dryer with this genuine OEM push-to-start switch, designed specifically for use with a range of GE dryer models. This switch activates the dryer when you press an...
$30.95
In Stock
Order within the next 12 hrs and your part ships today!
This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on ...
$19.95
In Stock
Order within the next 12 hrs and your part ships today!
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. ...
$33.95
In Stock
Order within the next 12 hrs and your part ships today!
This is a replacement lint filter slide for your dryer. It is approximately 14 inches long and 5 inches wide. It is made of white plastic and is sold individually. The slide mounts to your dryer and a...
$55.81
In Stock
Order within the next 12 hrs and your part ships today!
This is a door handle made for use with dryers. This door handle is made of solid white plastic and allows you to open and close the door of the dryer. If your current dryer door handle is broken or m...
$68.55
In Stock
Order within the next 12 hrs and your part ships today!
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
$13.95
In Stock
Order within the next 12 hrs and your part ships today!
The door latch lid lock is to lock the door on your washer when the appliance is in use. Your washer will not start if your door is not locked. If your latch is broken, you may not be able to start a ...
$67.95
In Stock
Order within the next 12 hrs and your part ships today!
Questions And Answers for GUD24ESSJ0WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
15 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carlvin
January 29, 2020
Water is not filling up enough to do a load
For model number GUD24ESSJ0WW
Hello and thank you for writing.
It certainly sounds like it could be a faulty pressure switch PS7320331 (The pressure switch detects the water level in the tub. ) and or the water inlet assembly PS9491778, you should check the part(s) for signs of damage or test with a multimeter, and replace it as needed. we have attached the part links related to this question for your convenience. We hope this helps. Please contact us anytime if you require further assistance.
Hello, My washer will not close the DRAIN when filling. I unplug it and plug it back in and it works for a few loads.
What part or sensor do I need to fix my problem.?
For model number GUD24ESSJ0WW
Hi Helen, thank you for contacting us. We have researched the model and would suggest making sure the house drain pipe is at least 30 inches high. If so, check to make sure the drain hose is not pushed too far down into the drain. There must be an air gap around the drain hose. A snug fit can cause a siphoning action. If the issue remains, the problem might be with the drain pump, part number PS12171618, itself. There is a chance that it might be grounded out, making it run even when there’s no more water for it to drain from the washer. Checking the drain pump for continuity using a multimeter might help. Good luck with this repair!
The Washer won't start. Everything else seems to be fine except the start button for the washer.
For model number GUD24ESSJ0WW
Hello Melia, thank you for reaching out. Based on our understanding of the issue, we would suggest checking the button selector, part number PS11726734, to solve the problem. We hope this helps!
Hello Tricia, thank you for getting in touch. According to our research, the issue is most probably with the water inlet valve, part number PS12343369. You may need to replace it to fix the issue. We hope this helps!
The washing machine will start but the washing machine will NOT SPIN. It drains the water and then it should start spinning BUT instead it shuts down and the status light starts to blink.
For model number GUD24ESSJ0WW
Hi Nicky,
Thank you for your question. If your washer will not spin, we recommend checking the lid lock and switch assembly. The lid switch is used as a safety device to prevent the motor circuit from operating when the lid is open. If the lid switch fails, the washer may not spin. To verify if the switch is operating normally, you will need to test it. Unplug the washer from the electrical outlet and check and see if the switch is operating mechanically by inspecting the levers and actuators for any signs of damage and to make sure that they are not sticking. If there are no mechanical issues, you will need to test it with a multimeter for continuity. Set your multimeter to the Rx1 setting and touch the probes to the terminals. You should receive a reading of zero. If you get a reading that is not zero, you will need a replacement lid lock and switch assembly. We hope this helps!
It was actually my father, he doesn't use the internet. He thought that because the dyer got real hot and then shut off he thought the thermostat wasn't working and the high temp shutoff was okay. He went through the manual and found the part and took it out. He called the service number but they wanted $50 dollars plus shipping. I saw it
... Read more was a Thermo-disc part so I tried the manufacture's website but I couldn't match the numbers on the back to their part numbers. I tried several other sites and your site was the cheapest. It was real easy to use the web site and diagrams to find the right schematic and part. I ordered it online and it was delivered in 2 days with the regular shipping. When he first put it in the dyer didn't turn on. He found no power coming out of the timer so he cleaned the contacts and it worked. Thanks for making the ordering so easy.
The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a pow
... Read moreer fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.
