Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
$13.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$22.95
In Stock
Order now and your part arrives in 2-3 business days!
Perfect for your GE washer, the Nut Hub is designed to secure the washer hub to the gear case shaft with precision. It plays a crucial part in ensuring the appliance runs smoothly and efficiently. The...
$19.95
In Stock
Order now and your part arrives in 2-3 business days!
Upgrade your washer with the reliable Washer Hub from GE. This essential component, often referred to as the hub nut, offers sturdiness and quality that GE products are known for. Before installation,...
$14.95
In Stock
Order now and your part arrives in 2-3 business days!
Introducing the GE Drain Hose, specifically designed for washing machines. This essential accessory safely transports used water from your washer directly to your house drain, establishing an efficien...
$45.95
In Stock
Order now and your part arrives in 2-3 business days!
This part is the replacement suspension rod and spring assembly for your washer. The rod is approximately 25 inches long and is sold individually. The suspension rod and spring works like a shock abso...
$35.95
In Stock
Order now and your part arrives in 2-3 business days!
Order now and your part arrives in 2-3 business days!
Questions And Answers for GTWS8350H1WS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Edward
December 26, 2019
Cloth napkin partially stuck under agitator. How do I remove it?
For model number GTWS8350H1WS
Hello Edward, Thank you for the question. There is a round cap at the top of the agitator. You can pop the cap off with a flat head screw driver. Once removed there is a bolt you can unscrew to remove the agitator. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Tim
June 28, 2022
"Power" on switch lights up. "Start" button does not depress, won't start.
For model number GTWS8350H1WS
Hello Tim, Thank you for the question. The Start Button is only sold as part of the Backsplash, PartSelect Number PS8757307. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
How to remove the control panel on a GE washer model # GTWS8350H1WS
For model number GTWS8350H1WS
Hello George, thank you for reaching out. We are providing you with instructions that will help you replace the control panel.
1- Unthread the screws from the rear control panel.
2- Remove the control knob from the control panel by pulling it up.
3- Remove the top panel by using a putty knife.
4- Unthread the two screws securing the control panel from the front.
5- Disconnect the wires from the electronic control board.
6- Replace the control panel with the new one.
We hope this helps!
Was this helpful?
Thank you for voting!
Larry
August 23, 2023
will nofill to start nor will it spen
For model number GTWS8350H1WS
Hi Larry, thank you for getting in touch. We have concluded that the issue is with the lid lock assembly, part number PS11701133. We would recommend checking the lid lock assembly to fix the issue. We hope that helps!
Hi Ronald, thank you for contacting us. We have found that the start button on the control panel is not sold separately. You may need to order the entire backsplash body assembly, part number PS8757307. We hope this information helps!
This procedure was completely different from any other Tub Seal I've done and in my opinion needs 2 people. The first thing to note is that this seal must be removed from the bottom of the outer tub. Also, the top of this machine does not hinge in back. The typical clips are in front, but the back has 2 screws that must be removed. Since
... Read morethe wiring was too involved to completely separate the top from the base, I had to improvise a stand to hold the top while the rest of the process was completed - keep slack on all remaining connected wires. The motor, clutch and bearing plate must be removed from the bottom in order to access the Tub Seal. Below are the steps I did to complete the process: - Remove Control Panel Cover (rear) - Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well) - Remove Pressure Switch - Disconnect Detergent and Softener dispense hoses from Machine Top - Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires. - Remove Tub Cover - Remove Impeller (Agitator) from inside tub. - Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact) - Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall) - Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal. - Replace Cross bar to keep unit stable - Lay machine on its side - use care not stretch or pull any wires. - Remove motor, (Rotor and Stator) - Remove Clutch and wires - Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate - Remove all screws securing Bearing Plate to Outer Tub - Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care) - Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap) - Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires. - During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
Secured power and supply lines. Took off rear panel. Labeled all 5 electrical inputs to water valve. Could not get water valve out. Found the 5 hoses that were clamped to the 5 valve inputs by going head first into the washer. Did not order the clamps!!!! Even if we had, we couldn't figure out how to access them. Called appliance guys who
... Read more installed valve and clamps.
