Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash c...
$34.95
In Stock
Order now and your part arrives in 2-3 business days!
This set (Knob and Clip Assembly, Control Knob, Dryer Control Knob) allows you to replace the knob on your timer if it is damaged or missing. The plastic knob can break around its shaft, or the retain...
$37.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a replacement timer knob for your washing machine. To complete this repair you will need a pair of needle nose pliers. Turn off power to the washer before you start. Pull off the timer knob an...
$12.95
In Stock
Order now and your part arrives in 2-3 business days!
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drai...
$30.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a dual-action agitator for a washer. It is an OEM replacement part that is sourced from the manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action a...
$53.70
In Stock
Order now and your part arrives in 2-3 business days!
This timer dial with compression ring shows you which part of the cycle your washer is in. It is white in color and can be found mounted on the timer shaft. You may need to replace this part if your ...
$15.95
In Stock
Order now and your part arrives in 2-3 business days!
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at ...
$18.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a w...
$13.95
In Stock
Order now and your part arrives in 2-3 business days!
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. T...
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
$38.95
In Stock
Order now and your part arrives in 2-3 business days!
Ask our experts a question about this model and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lisa
August 12, 2021
I am getting black marks on clothing that is near the bottom of the basket, up against the tub after the spin cycle. I have cleaned the washer using vinegar and bleach, but it is still happening. Not sure what is causing this.
For model number GTWN2800D0WW
Hello Lisa, Thank you for the question. This is normally caused by a worn or defective Tub Oil Seal, PartSelect Number PS4704237. We hope this helps!
The cold water valve will not open during a normal cycle when "Cold" is selected at the temperature selector. The cold water valve will energize during a rinse cycle, though. I have replaced the temperature selector switch. What is my next step?
For model number GTWN2800D0WW
Hi Vince,
Thank you for your question. If the cold water valve will not open during the normal cycle. the issue may be with the lid switch assembly. The lid switch on a top load washing machine is a safety device designed to prevent the motor circuit from operating when the lid is open. On some models, the water inlet valve circuit is also controlled by the lid switch. If the lid switch fails on these models, power cannot be supplied to the water inlet valve. If you have determined that the water inlet valve on your washer is not receiving power, then you should check the lid switch. Before removing and testing the lid switch from the washer, please unplug the washer from the electrical outlet. Once you have located it, verify that the actuators or levers are not sticking or damaged and that the switch is being operated mechanically. If no issues are found above, remove the switch in order to test it for continuity and set your multimeter to Rx1. While pressing in on the switch’s button, touch the terminals with the probes. You should receive a reading of zero or nearly zero. If you receive a different reading, you will need a replacement lid switch. If the lid switch is fine, you will need to check the water inlet valve and the timer. We hope this helps! If you have any questions, please let us know.
What would cause the washer to shake violently to the point where the console would come loose? Assume the washer is level.
For model number GTWN2800D0WW
Hello Michael, thank you for getting in touch. Based on our understanding of the issue, we would suggest replacing the shock dampening device, part number PS271100, to solve the problem. We hope this helps!
The above belong to a clothes washer which leaves lint on clothing after wash..is there a filter that need to be replaced in the washer. thank u
For model number GTWN2800D0WW
Hello Daniel,
Thank you for your question. We apologize, but the part you're looking for is discontinued and no longer available from our website. We suggest getting in contact with the manufacturer to find a substitute replacement part that would be compatible to your model. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joseph
December 8, 2024
The wash machine won't drain
For model number GTWN2800D0WW
Hello Joseph, Thank you for your inquiry. We would recommend checking the drain pump and drain hoses for any clogs and you can also test the drain pump with a multimeter. Good luck with your repair.
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
