Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
$73.45
In Stock
Order now and your part arrives in 2-3 business days!
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
$44.95
In Stock
Order now and your part arrives in 2-3 business days!
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
$19.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
$21.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
$33.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
$49.93
In Stock
Order now and your part arrives in 2-3 business days!
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger...
$51.11
In Stock
Order now and your part arrives in 2-3 business days!
This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spi...
$25.95
In Stock
Order now and your part arrives in 2-3 business days!
This is an inlet valve for models of compatible washing machines. Inlet valves are electrically controlled solenoid valves that open and close as needed during the washing cycle, to allow water into t...
$60.34
In Stock
Order now and your part arrives in 2-3 business days!
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
$33.95
In Stock
Order now and your part arrives in 2-3 business days!
Introducing the GE Spring Clutch, a crucial component for your washer. This intricate item applies steadfast pressure against the shifter hub, dutifully holding it in place for uninterrupted operation...
$13.95
In Stock
Order now and your part arrives in 2-3 business days!
Questions And Answers for GTW685BSL0WS
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
November 17, 2022
looking to see if this washer has a filter, if so where is it located
For model number GTW685BSL0WS
Hi David, thank you for contacting us. Your model does not have any filter. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
PHILLIP
October 21, 2024
I HAVE AN GE WASHER WAS WORKING FINE THAN IT STOP DRAINING AND SPINING THE DOOR LOCKS AND THE INTERFACE BOARD SHOW 11 MIN AND COUNTS DOWN TO 9 SEC AND DOES NOT START THE DRAIN AND SPIN CYCLE WHAT MAY I POSSIBLY CHECK TO REPAIR WASHER
For model number GTW685BSL0WS
Hello Phillip, Thank you for your inquiry. Researching your model, we would recommend checking the speed sensor, the mode shifter, and the drain pump. You can test the parts with a multimeter. Good luck with your repair.
Super loud when spinning, almost like a worn bearing or something.
For model number GTW685BSL0WS
Hello Lance, thank you for getting in touch. Check the drive transmission or gear case assembly, part number PS16729511. It might be worn out or defective. They have gears in them which can fail, causing the washer to be noisy during operation. Check the drive pulley, part number PS16554753. The drive pulley makes the connection between the transmission and the inner tub. If the pulley is worn out, the washer will make loud noises. You will also need to check the drive belt, part number PS11736832. The belt gets loose over time due to damage or wear and tear, which can cause loud noise. We hope this helps.
I just replaced the water valve assembly because water was dripping non stop into the tub but now the tub is over-filling and says h20 supply and then drains out. Water no longer drips into the tub though...
For model number GTW685BSL0WS
Hello Lesley,
Thank you for your question. We suggest using a multi-meter to check the water valve you ordered from us to make sure it isn't defective. Typically if the washer is overflowing or if there is a leak its both caused by the valve itself since it controls the water output. We hope this helps.
Softner dispenser fails to dispense. I cleaned the inside same under the cap.
For model number GTW685BSL0WS
Hello Don, thank you for your question. We have researched your model and found that the issue is probably with the water inlet valve, part number PS12171559. The dispenser utilizes water from the inlet valve to flush out the detergent and fabric softener. Slow water flow will cause the dispenser to not distribute the detergent and softener properly. If you require assistance placing an order, please contact customer service. We hope that helps!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Removed the control panel back plate cover. Removed the 3 screws that held the water control valve in place. I then unplugged each solenoid one at a time and plugged it into the new control valve. Once all wires were transferred, I pulled the old valve up and put the new valve on. Then reinstalled the screws that held it down and reinstal
... Read moreled the cover plate. Very simple job !
